Add Z1RCC Support

- Added build support for Bill Chen's Z1RCC.
- Thanks and credit to Bill for supplying the bulk of the build changes.

ReadMe.md

@@ -3,7 +3,7 @@
 **RomWBW ReadMe** \
 Version 3.4 \
 Wayne Warthen  ([[email protected]](mailto:[email protected])) \
-19 Oct 2023
+30 Oct 2023
 
 # Overview
 

ReadMe.txt

@@ -1,6 +1,6 @@
 RomWBW ReadMe
 Wayne Warthen ([email protected])
-19 Oct 2023
+30 Oct 2023
 
 
 

Source/Build.cmd

@@ -8,6 +8,7 @@ call BuildShared || exit /b
 call BuildImages || exit /b
 call BuildROM %* || exit /b
 call BuildZRC || exit /b
+call BuildZ1RCC || exit /b
 call BuildZZRCC || exit /b
 
 if "%1" == "dist" (

Source/BuildZ1RCC.cmd

@@ -0,0 +1,4 @@
+@echo off
+setlocal
+
+pushd Z1RCC && call Build || exit /b & popd

Source/Clean.cmd

@@ -22,4 +22,5 @@ pushd Prop && call Clean & popd
 pushd RomDsk && call Clean & popd
 pushd Doc && call Clean & popd
 pushd ZRC && call Clean & popd
+pushd Z1RCC && call Clean & popd
 pushd ZZRCC && call Clean & popd

Source/Doc/UserGuide.md

@@ -201,6 +201,7 @@ below, **carefully** pick the appropriate ROM image for your hardware.
 | [Nhyodyne Z80 MBC]^1^                                          | MBC     | MBC_std.rom        | 38400         |
 | [Rhyophyre Z180 SBC]^1^                                        | -       | RPH_std.rom        | 38400         |
 | [Z80 ZRC CPU Module]^7^                                        | RCBus   | RCZ80_zrc.rom      | 115200        |
+| [Z180 Z1RCC CPU Module]^7^                                     | RCBus   | RCZ180_z1rcc.rom   | 115200        |
 | [Z280 ZZRCC CPU Module]^7^                                     | RCBus   | RCZ280_zzrc.rom    | 115200        |
 | [Z280 ZZ80MB SBC]^7^                                           | RCBus   | RCZ280_zz80mb.rom  | 115200        |
 | [Z80-Retro SBC]^8^                                             | -       | Z80RETRO_std.rom   | 38400         |
@@ -4255,7 +4256,29 @@ the RomWBW HBIOS configuration.
    - VGARC Video & Keyboard Module
  - Serial baud rate is usually determined by hardware for ACIA and
    SIO interfaces
+
+### Z180 Z1RCC CPU Module
+
+|                   |                    |
+|-------------------|--------------------|
+| ROM Image Files   | RCZ180_z1rcc.rom   |
+| Console Baud Rate | 115200             |
+| Interrupts        | Mode 2             |
 
+ - CPU speed is detected at startup if DS1302 RTC is active
+   - Otherwise 18.432 MHz assumed
+ - System timer is generated by Z180 CPU
+ - Hardware auto-detected:
+   - DS1302 RTC
+   - Z180 ASCI Serial Ports
+   - SIO Serial Interface Module
+   - EP Dual UART Serial Interface Module
+   - WDC Floppy Disk Controller w/ 3.5" HD Drives
+   - IDE Hard Disk Interface Module
+   - PPIDE Hard Disk Interface Module
+ - Use of Interrupt Mode 2 requires proper IEI/IEO configuration
+   for all peripherals generating interrupts
+
 `\clearpage`{=latex}
 
 ### Z280 ZZRCC CPU Module

Source/HBIOS/Build.cmd

@@ -216,6 +216,7 @@ call Build RCZ80 zrc || exit /b
 call Build RCZ80 zrc_ram || exit /b
 call Build RCZ180 ext || exit /b
 call Build RCZ180 nat || exit /b
+call Build RCZ180 z1rcc || exit /b
 call Build RCZ280 ext || exit /b
 call Build RCZ280 nat || exit /b
 call Build RCZ280 zz80mb || exit /b

Source/HBIOS/Build.sh

@@ -15,6 +15,7 @@ if [ "${ROM_PLATFORM}" == "dist" ] ; then
 	ROM_PLATFORM="N8"; ROM_CONFIG="std"; bash Build.sh
 	ROM_PLATFORM="RCZ180"; ROM_CONFIG="ext"; bash Build.sh
 	ROM_PLATFORM="RCZ180"; ROM_CONFIG="nat"; bash Build.sh
+	ROM_PLATFORM="RCZ180"; ROM_CONFIG="z1rcc"; bash Build.sh
 	ROM_PLATFORM="RCZ280"; ROM_CONFIG="ext"; bash Build.sh
 	ROM_PLATFORM="RCZ280"; ROM_CONFIG="nat"; bash Build.sh
 	ROM_PLATFORM="RCZ280"; ROM_CONFIG="zz80mb"; bash Build.sh

Source/HBIOS/Config/RCZ180_z1rcc.asm

@@ -0,0 +1,76 @@
+;
+;==================================================================================================
+;   RCBUS Z180 Z1RCC CONFIGURATION (ROMLESS)
+;==================================================================================================
+;
+; THE COMPLETE SET OF DEFAULT CONFIGURATION SETTINGS FOR THIS PLATFORM ARE FOUND IN THE
+; CFG_<PLT>.ASM INCLUDED FILE WHICH IS FOUND IN THE PARENT DIRECTORY.  THIS FILE CONTAINS
+; COMMON CONFIGURATION SETTINGS THAT OVERRIDE THE DEFAULTS.  IT IS INTENDED THAT YOU MAKE
+; YOUR CUSTOMIZATIONS IN THIS FILE AND JUST INHERIT ALL OTHER SETTINGS FROM THE DEFAULTS.
+; EVEN BETTER, YOU CAN MAKE A COPY OF THIS FILE WITH A NAME LIKE <PLT>_XXX.ASM AND SPECIFY
+; YOUR FILE IN THE BUILD PROCESS.
+;
+; THE SETTINGS BELOW ARE THE SETTINGS THAT ARE MOST COMMONLY MODIFIED FOR THIS PLATFORM.
+; MANY OF THEM ARE EQUAL TO THE SETTINGS IN THE INCLUDED FILE, SO THEY DON'T REALLY DO
+; ANYTHING AS IS.  THEY ARE LISTED HERE TO MAKE IT EASY FOR YOU TO ADJUST THE MOST COMMON
+; SETTINGS.
+;
+; N.B., SINCE THE SETTINGS BELOW ARE REDEFINING VALUES ALREADY SET IN THE INCLUDED FILE,
+; TASM INSISTS THAT YOU USE THE .SET OPERATOR AND NOT THE .EQU OPERATOR BELOW. ATTEMPTING
+; TO REDEFINE A VALUE WITH .EQU BELOW WILL CAUSE TASM ERRORS!
+;
+; PLEASE REFER TO THE CUSTOM BUILD INSTRUCTIONS (README.TXT) IN THE SOURCE DIRECTORY (TWO
+; DIRECTORIES ABOVE THIS ONE).
+;
+#DEFINE PLATFORM_NAME "Z1RCC", " [", CONFIG, "]"
+;
+#DEFINE	BOOT_DEFAULT	"H"		; DEFAULT BOOT LOADER CMD ON <CR> OR AUTO BOOT
+;
+#include "cfg_rcz180.asm"
+;
+CPUOSC		.SET	18432000	; CPU OSC FREQ IN MHZ
+CRTACT		.SET	FALSE		; ACTIVATE CRT (VDU,CVDU,PROPIO,ETC) AT STARTUP
+;
+FPLED_ENABLE	.SET	TRUE		; FP: ENABLES FRONT PANEL LEDS
+FPSW_ENABLE	.SET	TRUE		; FP: ENABLES FRONT PANEL SWITCHES
+;
+MEMMGR		.SET	MM_Z180		; MEMORY MANAGER: MM_[SBC|Z2|N8|Z180]
+;
+RAMSIZE		.SET	512		; SIZE OF RAM IN KB (MUST MATCH YOUR HARDWARE!!!)
+ROMSIZE		.SET	0		; SIZE OF ROM IN KB (MUST MATCH YOUR HARDWARE!!!)
+;
+Z180_CLKDIV	.SET	1		; Z180: CHK DIV: 0=OSC/2, 1=OSC, 2=OSC*2
+Z180_MEMWAIT	.SET	0		; Z180: MEMORY WAIT STATES (0-3)
+Z180_IOWAIT	.SET	1		; Z180: I/O WAIT STATES TO ADD ABOVE 1 W/S BUILT-IN (0-3)
+;
+MDROM		.SET	FALSE		; MD: ENABLE ROM DISK
+MDRAM		.SET	TRUE		; MD: ENABLE RAM DISK
+;
+DSRTCENABLE	.SET	TRUE		; DSRTC: ENABLE DS-1302 CLOCK DRIVER (DSRTC.ASM)
+INTRTCENABLE	.SET	TRUE		; ENABLE PERIODIC INTERRUPT CLOCK DRIVER (INTRTC.ASM)
+;
+UARTENABLE	.SET	TRUE		; UART: ENABLE 8250/16550-LIKE SERIAL DRIVER (UART.ASM)
+ASCIENABLE	.SET	TRUE		; ASCI: ENABLE Z180 ASCI SERIAL DRIVER (ASCI.ASM)
+ACIAENABLE	.SET	FALSE		; ACIA: ENABLE MOTOROLA 6850 ACIA DRIVER (ACIA.ASM)
+SIOENABLE	.SET	TRUE		; SIO: ENABLE ZILOG SIO SERIAL DRIVER (SIO.ASM)
+;
+TMSENABLE	.SET	FALSE		; TMS: ENABLE TMS9918 VIDEO/KBD DRIVER (TMS.ASM)
+TMSMODE		.SET	TMSMODE_MSX	; TMS: DRIVER MODE: TMSMODE_[SCG|N8|MBC|MSX|MSX9958|MSXKBD|COLECO]
+MKYENABLE	.SET	FALSE		; MSX 5255 PPI KEYBOARD COMPATIBLE DRIVER (REQUIRES TMS VDA DRIVER)
+VRCENABLE	.SET	FALSE		; VRC: ENABLE VGARC VIDEO/KBD DRIVER (VRC.ASM)
+VDAEMU_SERKBD	.SET	0		; VDA EMULATION: SERIAL KBD UNIT #, OR $FF FOR HW KBD
+;
+;
+AY38910ENABLE	.SET	FALSE		; AY: AY-3-8910 / YM2149 SOUND DRIVER
+AYMODE		.SET	AYMODE_RCZ180	; AY: DRIVER MODE: AYMODE_[SCG|N8|RCZ80|RCZ180|MSX|LINC]
+SN76489ENABLE	.SET	FALSE		; SN: ENABLE SN76489 SOUND DRIVER
+;
+FDENABLE	.SET	TRUE		; FD: ENABLE FLOPPY DISK DRIVER (FD.ASM)
+FDMODE		.SET	FDMODE_RCWDC	; FD: DRIVER MODE: FDMODE_[DIO|ZETA|ZETA2|DIDE|N8|DIO3|RCSMC|RCWDC|DYNO|EPFDC]
+;
+IDEENABLE	.SET	TRUE		; IDE: ENABLE IDE DISK DRIVER (IDE.ASM)
+PPIDEENABLE	.SET	TRUE		; PPIDE: ENABLE PARALLEL PORT IDE DISK DRIVER (PPIDE.ASM)
+SDENABLE	.SET	FALSE		; SD: ENABLE SD CARD DISK DRIVER (SD.ASM)
+SDCNT		.SET	1		; SD: NUMBER OF SD CARD DEVICES (1-2), FOR DSD/SC/MT SC ONLY
+;
+PRPENABLE	.SET	FALSE		; PRP: ENABLE ECB PROPELLER IO BOARD DRIVER (PRP.ASM)

Source/Makefile

@@ -2,7 +2,7 @@
 # order is actually important, because of build dependencies
 #
 
-.PHONY: doc prop shared bp images rom zrc zzrcc
+.PHONY: doc prop shared bp images rom zrc z1rcc zzrcc
 
 .ONESHELL:
 .SHELLFLAGS = -cex
@@ -44,6 +44,9 @@ rom:
 zrc:
 	$(MAKE) --directory ZRC $(ACTION)
 
+z1rcc:
+	$(MAKE) --directory Z1RCC $(ACTION)
+
 zzrcc:
 	$(MAKE) --directory ZZRCC $(ACTION)
 

Source/Z1RCC/Bank Layout.txt

@@ -0,0 +1,20 @@
+Z1RCC has no real ROM.  It has a single 512K RAM chip.  The RomWBW
+ROMless startup mode is used.
+
+The ROMless startup mode treats the entire 512KB as RAM.  The entire 
+512KB of RAM (less the top 32KB) must be preloaded by the Z1RCC CF 
+Loader.  There will be no ROM disk available under RomWBW.  There will 
+be a RAM Disk and it's initial contents will be seeded by the image 
+loaded by the CF Loader.
+
+Bank		Contents	Description
+--------	--------	-----------
+0x0		BIOS		HBIOS Bank (operating)
+0x1		IMG0		ROM Loader, Monitor, ROM OSes
+0x2		IMG1		ROM Applications
+0x3		IMG2		Reserved
+0x4-0xB		RAMD		RAM Disk Banks
+0xC		BUF		OS Buffers (CP/M3)
+0xD		AUX		Aux Bank (CP/M 3, BPBIOS, etc.)
+0xE		USR		User Bank (CP/M TPA, etc.)
+0xF		COM		Common Bank, Upper 32KB

Source/Z1RCC/Build.cmd

@@ -0,0 +1,23 @@
+@echo on
+setlocal
+
+set TOOLS=../../Tools
+
+set PATH=%TOOLS%\srecord;%PATH%
+
+if exist ..\..\Binary\RCZ180_z1rcc.rom call :build_z1rcc
+
+goto :eof
+
+:build_z1rcc
+
+srec_cat -generate 0x0 0x100000 --constant 0x00 -o temp.dat -binary
+srec_cat temp.dat -binary -exclude 0x0 0x200 z1rcc_cfldr.bin -binary -o temp.dat -binary
+srec_cat temp.dat -binary -exclude 0x1B8 0x200 z1rcc_ptbl.bin -binary -offset 0x1B8 -o temp.dat -binary
+srec_cat temp.dat -binary -exclude 0x1F000 0x20000 z1rcc_mon.bin -binary -offset 0x1F000 -o temp.dat -binary
+srec_cat temp.dat -binary -exclude 0x24000 0xA4000 ..\..\Binary\RCZ180_z1rcc.rom -binary -offset 0x24000 -o temp.dat -binary
+move temp.dat ..\..\Binary\hd1k_z1rcc_prefix.dat
+
+copy /b ..\..\Binary\hd1k_z1rcc_prefix.dat + ..\..\Binary\hd1k_cpm22.img + ..\..\Binary\hd1k_zsdos.img + ..\..\Binary\hd1k_nzcom.img + ..\..\Binary\hd1k_cpm3.img + ..\..\Binary\hd1k_zpm3.img + ..\..\Binary\hd1k_ws4.img ..\..\Binary\hd1k_z1rcc_combo.img || exit /b
+
+goto :eof

Source/Z1RCC/Clean.cmd

@@ -0,0 +1,3 @@
+@echo off
+setlocal
+

Source/Z1RCC/Makefile

@@ -0,0 +1,30 @@
+HD1KZ1RCCPREFIX = hd1k_z1rcc_prefix.dat
+HD1KZ1RCCCOMBOIMG = hd1k_z1rcc_combo.img
+Z1RCCROM = ../../Binary/RCZ180_z1rcc.rom
+HD1KIMGS = ../../Binary/hd1k_cpm22.img ../../Binary/hd1k_zsdos.img ../../Binary/hd1k_nzcom.img \
+	../../Binary/hd1k_cpm3.img ../../Binary/hd1k_zpm3.img ../../Binary/hd1k_ws4.img
+
+OBJECTS :=
+
+ifneq ($(wildcard $(Z1RCCROM)),)
+	OBJECTS += $(HD1KZ1RCCPREFIX) $(HD1KZ1RCCCOMBOIMG)
+endif
+
+DEST=../../Binary
+
+TOOLS = ../../Tools
+
+include $(TOOLS)/Makefile.inc
+
+DIFFPATH = $(DIFFTO)/Binary
+
+$(HD1KZ1RCCPREFIX):
+	srec_cat -generate 0x0 0x100000 --constant 0x00 -o temp.dat -binary
+	srec_cat temp.dat -binary -exclude 0x0 0x200 z1rcc_cfldr.bin -binary -o temp.dat -binary
+	srec_cat temp.dat -binary -exclude 0x1B8 0x200 z1rcc_ptbl.bin -binary -offset 0x1B8 -o temp.dat -binary
+	srec_cat temp.dat -binary -exclude 0x1F000 0x20000 z1rcc_mon.bin -binary -offset 0x1F000 -o temp.dat -binary
+	srec_cat temp.dat -binary -exclude 0x24000 0xA4000 $(Z1RCCROM) -binary -offset 0x24000 -o temp.dat -binary
+	mv temp.dat $@
+
+$(HD1KZ1RCCCOMBOIMG): $(HD1KZ1RCCPREFIX) $(HD1KIMGS)
+	cat $^ > $@

Source/Z1RCC/Z1RCC Disk Layout.txt

@@ -0,0 +1,24 @@
+Z1RCC Disk Prefix Layout
+======================
+
+---- Bytes ----   --- Sectors ---
+Start   Length    Start   Length    Description
+------- -------   ------- -------   ---------------------------
+0x00000 0x001BE   0       1         CF Boot Loader
+0x001B8 0x00048                     RomWBW Partition Table
+0x00200 0x1EE00   1       247       Unused
+0x1F000 0x01000   248     8         Z1RCC Monitor v0.2a
+0x20000 0x04000   256     32        Unused
+0x24000 0x80000   288     1024      RomWBW
+0xA4000 0x5C000   1312    736       Unused  
+0x100000          2048              Start of slices (partition 0x1E)
+
+Notes
+-----
+
+- At startup CPLD ROM is mapped to Z80 CPU address space 0x0000-0x003F, CPU begins execution at 0x0000
+- CPLD ROM (CF bootstrap mode) reads CF Boot Loader (512B) from start of CF (MBR) to 0xA000 and runs it
+- CF Boot Loader reads Z1RCC Monitor (4KB) from sectors 0xF8-0xFF of CF to 0xB000 and runs from 0xB400
+- Z1RCC Monitor reads 480KB (RomWBW) from sectors 0x120-0x4DF of CF into 480KB of physical RAM
+
+

Source/ver.inc

@@ -2,7 +2,7 @@
 #DEFINE	RMN	4
 #DEFINE	RUP	0
 #DEFINE	RTP	0
-#DEFINE BIOSVER	"3.4.0-dev.14"
+#DEFINE BIOSVER	"3.4.0-dev.15"
 #define rmj	RMJ
 #define rmn	RMN
 #define rup	RUP

Source/ver.lib

@@ -3,5 +3,5 @@ rmn	equ	4
 rup	equ	0
 rtp	equ	0
 biosver	macro
-	db	"3.4.0-dev.14"
+	db	"3.4.0-dev.15"
 	endm