======================================
Wireless Mesh Software Defined Network
======================================

A collection of scripts for running wireless mesh networks using OpenFlow/OpenvSwitch.

http://netgroup.uniroma2.it/wmSDN/


Installation steps (tested on  Ubuntu 12.04)
============================================

# install CORE:
wget http://downloads.pf.itd.nrl.navy.mil/core/packages/4.5/core-daemon_4.5-0ubuntu1_precise_amd64.deb
sudo dpkg -i core-daemon_4.5-0ubuntu1_precise_amd64.deb
sudo apt-get install -f


# get wmSDN
sudo apt-get install git
git clone https://github.com/netgroup/wmSDN.git
cd wmSDN
git submodule init
git submodule update


# build and install olsrd
cd olsrd
make && make libs
sudo make install_libs
cd ..


# build openvswitch
cd openvswitch
sudo apt-get install automake libtool libssl-dev
./boot.sh
./configure
make
# build the kernel module
./configure --with-linux=/lib/modules/`uname -r`/build
make
sudo rmmod openvswitch
sudo insmod ./datapath/linux/openvswitch.ko
cd ..


# prepare POX
cd pox/ext
ln -sv ../../controller/*.py .
cd ../pox/openflow
ln -s ../../../controller/other_modules/of_json.py .
cd ../lib
ln -s ../../../controller/other_modules/utill.py .
cd ../../..
sudo apt-get install python-networkx


# check that the directories in the scripts exist and
# change them as needed.
# e.g. change all occurrencies of /home/user to the home 
# directory of the current user
grep openvswitch scripts/*.sh

# install iperf
apt-get install iperf

# install NS3
cd ~
wget http://www.nsnam.org/release/ns-allinone-3.17.tar.bz2
tar xf ns-allinone-3.17.tar.bz2
cd ns-allinone-3.17/
sudo apt-get install build-essential
sudo apt-get install gcc g++ python python-dev
sudo apt-get install gsl-bin libgsl0-dev libgsl0ldbl
sudo apt-get install vtun lxc
sudo apt-get install flex bison libfl-dev
sudo apt-get install tcpdump
sudo apt-get install libxml2 libxml2-dev
sudo apt-get install sqlite sqlite3 libsqlite3-dev
./build.py --enable-tests
cd ..


Usage
=====

# start the emulation
cd ~/ns-allinone-3.17/ns-3.17/
sudo ./waf shell
cd ~/wmSDN/emulation
cat coreconf.py #check the paths 
# start the actual emulation
core-cleanup.sh && python -i ./ns3SDN.py -d 7200

# on another shell
cd ~/wmSDN/emulation
./starthosts.sh && ./startovs.sh

# now the emulation should be up and running

# TOPOLOGY
# --------
#                    (controller)
#                         |
# (server)---(n1)  (n2)  (n3)  (n4)  (gw6)-+
#                         |                +---(client)
#                       (gw5)--------------+
#
#

# to get into one of the nodes, e.g. n2
source bashrc
corevcmd n2

# olsr writes into routing table 198
ip route show table 198

# see the flow table
source .bashrc
of_flows

# monitor active flows
of_watch_active_flows

# get some flow table stats
of_rule_stats

# exit the node's shell
exit


# starting the controller
cd ~/wmSDN/emulation
source bashrc
corevcmd controller
cd ~/wmSDN/pox
./pox.py gw_switch_olsrd


# PROGRESSIVE IPERF TEST
# a new iperf flow starts every 20 seconds
# from the client node to the server node
# try with and without the controller running
mkdir ~/iperftestresults
cd ~/wmSDN/emulation
# optionally enable TCP Reno
sudo ./tcp_reno.sh
./progressive_iperf.sh ~/iperftestresults
less ~/iperftestresults/iperf_s_11.log


# GATEWAY FAILOVER TEST
# two iperf flows are started, each flowing through a
# different gateway.
# Then, at t=180s one of the gateway fails and the 
# controller moves both flows to the running gateway.
# At t=360s the gateway comes up again, and the controller 
# re-balances the flows through both gateways.
# make sure the controller is running during the test.
mkdir ~/failovertestresults
cd ~/wmSDN/emulation
# optionally enable TCP Reno
sudo ./tcp_reno.sh
./failover_test.sh ~/failovertestresults
less ~/failovertestresults/iperf_s_11.out
less ~/faiolvertestresults/iperf_s_12.out


Contacts
========
 * wmSDN home page: http://netgroup.uniroma2.it/wmSDN/
 * wmSDN mailing list: https://groups.google.com/forum/#!forum/wmsdn
 * Claudio Pisa <[email protected]>