OpenCO2 Sensor using ESP32 and SCD4x

OpenCO2 Sensor is an Arduino IDE compatible Repository for an E-Ink Indoor air quality Sensor using the ESP32, SCD4X and an RBG LED.

Buy it here on Tindie

Especially in winter, when windows are closed, a reminder to ventilate regularly is useful for health, comfort and well-being. Poor indoor air quality can lead to decreased productivity and learning disabilities. Therefore, I developed an Open-source ESP32 project that uses an E-Ink display and a LED to show the indoor CO2 content. Take the small Sensor anywhere you go to monitor the Air Quality, with Battery life of 11+ days.

CO2 Sensor

With the SCD40, Sensirion offers a completely new miniaturized CO2 sensor based on the photoacoustic sensor principle. The integrated, industry-leading humidity and temperature sensor offers high accuracy with low power consumption.

• Automatic self-calibration ensures the highest long-term stability
• CO2 output range: 400 ppm – 40'000 ppm
• Accuracy:
  • CO2 ±(50ppm + 5% of reading)
  • Temperature ±0.8°C
  • Humidity ±6%

Clear E-Ink display

1.54" in size with a very high resolution (200x200 Pixel). Enables low power consumption and wide viewing angle. Per partial refresh, readings are updated every five seconds (every 30 seconds in battery mode).

RGB LED

For displaying the air quality as a traffic light (green, yellow, red, magenta). Brightness and color are adjustable via software.

3D-printed housing

Size: 4.7 x 4.1 x 2.4 cm

• 3D Model viewer
• 3D File FRONT
• 3D File BACK

Menu

Press the Menu button on the backside of the OpenCO2 Sensor. Select an option via long press (1+ sec) or move to next menu point via a short press. Choose between:

• LED toggle enable or disable the LED in battery mode
• Rainbow fun little easter egg (press ↪️ to exit)
• Calibrate put the sensor outside for 3+ minutes (only run this, if calibration is needed)
• History display up to 24 QR codes containing 1h of measurements each (only stored in battery mode)
• Wi-Fi enable or disable wireless connections
• Exit quit Menu (automatically after 20 sec)

Wi-Fi

Enable Wi-Fi via the Menu button. When power is connected, an access point OpenCO2 Sensor is enabled. Connect to it and navigate to http://192.168.4.1 (it will open automatically on modern Smartphones). Insert your home Wi-Fi credentials under Configure WiFi. Choose your network name from the list in the top and insert the password. Click Save. The sensor will now be automatically connected. Navigate to ip:9925 to see current co2/temperature/humidity measurements.

AirGradient / Grafana

Use internet-pi to store the CO2 / Temperature / Humidity data on your Pi. First connect the OpenCO2 Sensor to your Wi-Fi network and follow the instructions https://www.youtube.com/watch?v=Cmr5VNALRAg Then download the https://raw.githubusercontent.com/davidkreidler/OpenCO2_Sensor/main/grafana_OpenCO2_Sensor.json and import it into Grafana.

OTA Update

Download OpenCO2_Sensor.ino.bin from the latest release. Enable Wi-Fi via the Menu button, in an area where no previously known network is active. Connect power. Then connect to OpenCO2 Sensor and navigate to http://192.168.4.1 . Under Update select the OpenCO2_Sensor.ino.bin file and click Update. The Sensor will restart.

Update via USB

1. Download all files from the latest release
2. Make sure, that the power switch is in the ON position (down)
3. Plug a data USB-C cable into your PC and the Sensor
4. Hold the Button on the backside of the CO2 Sensor near the USB-C port and shortly push simultaneously the reset ↪️ Button
5. In Device Manager under Ports (COM & LPT) find the COM number and modify it in update.bat
6. Run update.bat
7. Afterwards push the reset ↪️ Button

Installation inside the Arduino IDE

1. Copy the esp32-waveshare-epd Folder to your Arduino/libraries/
2. Install the ESP32 support for Arduino IDE
3. Choose ESP32S2 Dev Module under Tools -> Board -> esp32
4. Connect the Sensor as described in step "Update to the latest release" and choose the new Port under Tools -> Boards -> Port

Dependencies

• Adafruit DotStar
• Sensirion Core
• Sensirion I2C SCD4x Arduino Library
• WiFiManager