Releases: arendst/Tasmota
Tasmota v14.4.1 Rudolph
RELEASE NOTES
Migration Information
This version removes support for direct migration from versions before v8.1.0 (Doris)
See migration path for instructions how to migrate to a major version.
Do not upgrade from minimal to minimal version. It will most likely fail at some point and will require flashing via serial. If you do have to use minimal versions, always OTA to a full version of the same release before applying next minimal version.
Pay attention to the following version breaks due to dynamic settings updates:
- Migrate to Sonoff-Tasmota 3.9.x
- Migrate to Sonoff-Tasmota 4.x
- Migrate to Sonoff-Tasmota 5.14 (http://ota.tasmota.com/tasmota/release_5.14.0/sonoff.bin) - NOTICE underscore as a dash is not supported in older versions
- Migrate to Sonoff-Tasmota 6.7.1 (http://ota.tasmota.com/tasmota/release_6.7.1/sonoff.bin) - NOTICE underscore as a dash is not supported in older versions
- Migrate to Tasmota 7.2.0 (http://ota.tasmota.com/tasmota/release-7.2.0/tasmota.bin)
--- Major change in parameter storage layout ---
- Migrate to Tasmota 8.5.1 (http://ota.tasmota.com/tasmota/release-8.5.1/tasmota.bin)
--- Major change in internal GPIO function representation ---
- Migrate to Tasmota 9.1 (http://ota.tasmota.com/tasmota/release-9.1.0/tasmota.bin.gz)
- Upgrade to latest release (http://ota.tasmota.com/tasmota/release/tasmota.bin.gz)
While fallback or downgrading is common practice it was never supported due to Settings additions or changes in newer releases. Starting with release v9.1.0 Imogen the internal GPIO function representation has changed in such a way that fallback is only possible to the latest GPIO configuration before installing v9.1.0.
Supported Core versions
This release will be supported from ESP8266/Arduino library Core version 2.7.8 due to reported security and stability issues on previous Core version. This will also support gzipped binaries.
This release will be supported from ESP32/Arduino library Core version v3.1.0.241206.
Support of ESP8266 Core versions before 2.7.8 and ESP32 Core versions before v3.1.0.241206 have been removed.
Support of TLS
In addition to TLS using fingerprints now also user supplied CA certs, AWS IoT and Azure IoT is supported. Read full documentation
Initial configuration tools
For initial configuration this release supports Webserver based WifiManager or Serial based command interface.
Initial installation
Easy initial installation of Tasmota can be performed using the Tasmota WebInstaller.
Provided Binary Downloads
ESP8266 or ESP8285 based
The following binary downloads have been compiled with ESP8266/Arduino library core version 2.7.8.
- tasmota.bin = The Tasmota version with most drivers for 1M+ flash. RECOMMENDED RELEASE BINARY
- tasmota-4M.bin = The Tasmota version with most drivers and filesystem for 4M+ flash.
- tasmota-AD.bin to tasmota-VN.bin = The Tasmota version in different languages for 1M+ flash.
- tasmota-lite.bin = The Lite version without most drivers and sensors for 1M+ flash.
- tasmota-knx.bin = The Knx version without some features but adds KNX support for 1M+ flash.
- tasmota-sensors.bin = The Sensors version adds more useful sensors for 1M+ flash.
- tasmota-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 1M+ flash.
- tasmota-display.bin = The Display version without Energy Monitoring but adds display support for 1M+ flash.
- tasmota-zbbridge.bin = The dedicated Sonoff Zigbee Bridge version for 2M+ flash.
- tasmota-zigbee.bin = The dedicated cc25xx Zigbee Bridge version for 4M+ flash.
Above binaries are also available as gzipped version allowing faster uploads.
Latest released binaries can be downloaded from
- https://github.com/arendst/Tasmota-firmware/tree/firmware/release-firmware
- http://ota.tasmota.com/tasmota/release
Historical binaries can be downloaded from
The latter links can be used for OTA upgrades too like OtaUrl http://ota.tasmota.com/tasmota/release/tasmota.bin.gz
ESP32, ESP32-C2, ESP32-C3, ESP32-C6, ESP32-S2 and ESP32-S3 based
The following binary downloads have been compiled with ESP32/Arduino library core version v3.1.0.241206.
- tasmota32.bin = The Tasmota version with most drivers including additional sensors and KNX for 4M+ flash. RECOMMENDED RELEASE BINARY
- tasmota32solo1.bin = The Tasmota version with most drivers including additional sensors and KNX for single core ESP32 and 4M+ flash.
- tasmota32s2.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-S2 with serial and 4M+ flash.
- tasmota32s2cdc.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-S2 with serial over embedded USB CDC only and 4M+ flash.
- tasmota32s3.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-S3 with USB HWCDC and fallback to serial and 4M+ flash.
- tasmota32c2.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C2 with serial and 4M+ flash.
- tasmota32c3.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C2 with USB HWCDC and fallback to serial and 4M+ flash.
- tasmota32c6.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C6 with USB HWCDC and fallback to serial and 4M+ flash.
- tasmota32-AD.bin to tasmota32-VN.bin = The Tasmota version in different languages for 4M+ flash.
- tasmota32-bluetooth.bin = The Bluetooth version adds BLE support for 4M+ flash.
- tasmota32-display.bin = The Display version without Energy Monitoring but adds display support for 4M+ flash.
- tasmota32-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 4M+ flash.
- tasmota32-lvgl.bin = The LVGL version adds Light and Versatile Graphics Library (LVGL) display support for 4M+ flash.
- tasmota32-nspanel.bin = The Sonoff NSPanel Smart Scene Wall Switch version with HASPmota display support.
- tasmota32-webcam.bin = The Webcam version adds webcam support for 4M+ flash.
- tasmota32-zbbridgepro.bin - The Sonoff Zigbee Bridge Pro version with CC2652P firmware load support.
Latest released binaries can be downloaded from
- https://github.com/arendst/Tasmota-firmware/tree/firmware/release-firmware
- https://ota.tasmota.com/tasmota32/release
Historical binaries can be downloaded from
The latter links can be used for OTA upgrades too like OtaUrl https://ota.tasmota.com/tasmota32/release/tasmota32.bin
Additional information
List of embedded modules.
Complete list of available feature and sensors.
Changelog v14.4.1 Rudolph
Added
Changed
- Display removed PWM control of backlight GPIO regression from v14.1.0
- SSL clean up remnants of old fingerprint algorithm #22645
- Berry make Leds animate calls reentrant #22643
Fixed
- Display DisplayMode adds a display device while not configured
- GUI display power button regression from v14.3.0.5 #15788
- MCP23xxx, PCF8574 and Shift595 power control when a display is configured regression from v14.3.0.7
- ESP32 rules operation priority regression from v13.3.0.4 #22636
Changelog v14.4.0 Rudolph
Added
- Command
WebColor20to control color of Button when Off - Command
SetOption161 1to disable display of state text #22515 - Command
SetOption162 1to disable adding export energy to energy today #22578 - DALI support for short addresses (gear) and groups
- DALI command
DaliGearto set max found gear to speed up scan response - DALI command
DaliGroupto add gear to groups - DALI command
DaliTargetto set light control broadcast, group number or gear number - DALI command
DaliGroupSliders 0..16to show GUI group sliders with feedback disablingDaliLight - DALI inverted signal configuration using GPIO DALI RX_i/TX_i
- Support for I2C over Serial #22444
- Support KNX for scripts #22429
- Support deep sleep (standby) for VL53L0X #22441
- Support for Shelly DALI Dimmer Gen3
- Support for HLK-LD2410S 24GHz smart wave motion sensor #22253
- Support for US AQI and EPA AQI in PMS5003x sensors #22294
- Support for MS5837 pressure and temperature sensor #22376
- Support for TM16...
Tasmota v14.3.0 Robert
RELEASE NOTES
Migration Information
This version removes support for direct migration from versions before v8.1.0 (Doris)
See migration path for instructions how to migrate to a major version.
Do not upgrade from minimal to minimal version. It will most likely fail at some point and will require flashing via serial. If you do have to use minimal versions, always OTA to a full version of the same release before applying next minimal version.
Pay attention to the following version breaks due to dynamic settings updates:
- Migrate to Sonoff-Tasmota 3.9.x
- Migrate to Sonoff-Tasmota 4.x
- Migrate to Sonoff-Tasmota 5.14 (http://ota.tasmota.com/tasmota/release_5.14.0/sonoff.bin) - NOTICE underscore as a dash is not supported in older versions
- Migrate to Sonoff-Tasmota 6.7.1 (http://ota.tasmota.com/tasmota/release_6.7.1/sonoff.bin) - NOTICE underscore as a dash is not supported in older versions
- Migrate to Tasmota 7.2.0 (http://ota.tasmota.com/tasmota/release-7.2.0/tasmota.bin)
--- Major change in parameter storage layout ---
- Migrate to Tasmota 8.5.1 (http://ota.tasmota.com/tasmota/release-8.5.1/tasmota.bin)
--- Major change in internal GPIO function representation ---
- Migrate to Tasmota 9.1 (http://ota.tasmota.com/tasmota/release-9.1.0/tasmota.bin.gz)
- Upgrade to latest release (http://ota.tasmota.com/tasmota/release/tasmota.bin.gz)
While fallback or downgrading is common practice it was never supported due to Settings additions or changes in newer releases. Starting with release v9.1.0 Imogen the internal GPIO function representation has changed in such a way that fallback is only possible to the latest GPIO configuration before installing v9.1.0.
Supported Core versions
This release will be supported from ESP8266/Arduino library Core version 2.7.8 due to reported security and stability issues on previous Core version. This will also support gzipped binaries.
This release will be supported from ESP32/Arduino library Core version v3.1.0.240926.
Support of ESP8266 Core versions before 2.7.8 and ESP32 Core versions before v3.1.0.240926 have been removed.
Support of TLS
In addition to TLS using fingerprints now also user supplied CA certs, AWS IoT and Azure IoT is supported. Read full documentation
Initial configuration tools
For initial configuration this release supports Webserver based WifiManager or Serial based command interface.
Initial installation
Easy initial installation of Tasmota can be performed using the Tasmota WebInstaller.
Provided Binary Downloads
ESP8266 or ESP8285 based
The following binary downloads have been compiled with ESP8266/Arduino library core version 2.7.8.
- tasmota.bin = The Tasmota version with most drivers for 1M+ flash. RECOMMENDED RELEASE BINARY
- tasmota-4M.bin = The Tasmota version with most drivers and filesystem for 4M+ flash.
- tasmota-AD.bin to tasmota-VN.bin = The Tasmota version in different languages for 1M+ flash.
- tasmota-lite.bin = The Lite version without most drivers and sensors for 1M+ flash.
- tasmota-knx.bin = The Knx version without some features but adds KNX support for 1M+ flash.
- tasmota-sensors.bin = The Sensors version adds more useful sensors for 1M+ flash.
- tasmota-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 1M+ flash.
- tasmota-display.bin = The Display version without Energy Monitoring but adds display support for 1M+ flash.
- tasmota-zbbridge.bin = The dedicated Sonoff Zigbee Bridge version for 2M+ flash.
- tasmota-zigbee.bin = The dedicated cc25xx Zigbee Bridge version for 4M+ flash.
Above binaries are also available as gzipped version allowing faster uploads.
Latest released binaries can be downloaded from
- https://github.com/arendst/Tasmota-firmware/tree/firmware/release-firmware
- http://ota.tasmota.com/tasmota/release
Historical binaries can be downloaded from
The latter links can be used for OTA upgrades too like OtaUrl http://ota.tasmota.com/tasmota/release/tasmota.bin.gz
ESP32, ESP32-C2, ESP32-C3, ESP32-C6, ESP32-S2 and ESP32-S3 based
The following binary downloads have been compiled with ESP32/Arduino library core version v3.1.0.240926.
- tasmota32.bin = The Tasmota version with most drivers including additional sensors and KNX for 4M+ flash. RECOMMENDED RELEASE BINARY
- tasmota32solo1.bin = The Tasmota version with most drivers including additional sensors and KNX for single core ESP32 and 4M+ flash.
- tasmota32s2.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-S2 with serial and 4M+ flash.
- tasmota32s2cdc.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-S2 with serial over embedded USB CDC only and 4M+ flash.
- tasmota32s3.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-S3 with USB HWCDC and fallback to serial and 4M+ flash.
- tasmota32c2.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C2 with serial and 4M+ flash.
- tasmota32c3.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C2 with USB HWCDC and fallback to serial and 4M+ flash.
- tasmota32c6.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C6 with USB HWCDC and fallback to serial and 4M+ flash.
- tasmota32-AD.bin to tasmota32-VN.bin = The Tasmota version in different languages for 4M+ flash.
- tasmota32-bluetooth.bin = The Bluetooth version adds BLE support for 4M+ flash.
- tasmota32-display.bin = The Display version without Energy Monitoring but adds display support for 4M+ flash.
- tasmota32-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 4M+ flash.
- tasmota32-lvgl.bin = The LVGL version adds Light and Versatile Graphics Library (LVGL) display support for 4M+ flash.
- tasmota32-nspanel.bin = The Sonoff NSPanel Smart Scene Wall Switch version with HASPmota display support.
- tasmota32-webcam.bin = The Webcam version adds webcam support for 4M+ flash.
- tasmota32-zbbridgepro.bin - The Sonoff Zigbee Bridge Pro version with CC2652P firmware load support.
Latest released binaries can be downloaded from
- https://github.com/arendst/Tasmota-firmware/tree/firmware/release-firmware
- https://ota.tasmota.com/tasmota32/release
Historical binaries can be downloaded from
The latter links can be used for OTA upgrades too like OtaUrl https://ota.tasmota.com/tasmota32/release/tasmota32.bin
Additional information
List of embedded modules.
Complete list of available feature and sensors.
Changelog v14.3.0 Robert
Added
- Command
SetOption69 1to enable Serial Bridge inverted Receive #22000 - Command
DaliWeb 1to enable light control for DALI broadcast address - Command
DaliSend <address>|<address+256>,<command>to send command (address+256 is repeat) on DALI bus - Command
DaliQuery <address>|<address+256>,<command>to send command (address+256 is repeat) on DALI bus and wait up to DALI_TIMEOUT ms for response - HX711 optional calibration precision option on command
Sensor34 2 <weight in gram> <precision>where<precision>is 1 to 20 #13983 - ESP8266 support for one-wire M1601 temperature sensor on DS18x20 GPIO #21376
- ESP8266 support for I2C CLK on GPIO16 #22199
- Support for I2C M5Unit (Mini)Scales using HX711 driver
- Support for DALI on ESP8266
- Support for RX8010 RTC as used in IOTTIMER #21376
- Support for BL0906 up to 6 channel energy monitor as used in Athom EM2/EM6 #22167
- Support for Sonoff SPM v1.3.0 #13447
- Energy command
PowerSet 60,230to calibrate both Current and Power with known resistive load of 60W at 230V using calibrated Voltage - Energy command
CurrentSet 60,230to calibrate both Power and Current with known resistive load of 60W at 230V using calibrated Voltage - ESP8266 experimental support for second I2C bus
- MQTT warning if trying to connect without TLS on a port that normally uses TLS #22175
- Energy Log level 4 message when (Calculated) Apparent Power is less than Active Power indicating wrong calibration #20653
- Support nexus protocol and calculation of separation limit to rc-switch library #21886
- KNX additional KnxTx functions and define KNX_USE_DPT9 #22071
- SML multi TRX line #22056
- Misubishi Electric HVAC Heat/Dry/Cool Auto operation mode [#22216](https://git...
Tasmota v14.2.0 Rita
RELEASE NOTES
Migration Information
This version removes support for direct migration from versions before v8.1.0 (Doris)
See migration path for instructions how to migrate to a major version.
Do not upgrade from minimal to minimal version. It will most likely fail at some point and will require flashing via serial. If you do have to use minimal versions, always OTA to a full version of the same release before applying next minimal version.
Pay attention to the following version breaks due to dynamic settings updates:
- Migrate to Sonoff-Tasmota 3.9.x
- Migrate to Sonoff-Tasmota 4.x
- Migrate to Sonoff-Tasmota 5.14 (http://ota.tasmota.com/tasmota/release_5.14.0/sonoff.bin) - NOTICE underscore as a dash is not supported in older versions
- Migrate to Sonoff-Tasmota 6.7.1 (http://ota.tasmota.com/tasmota/release_6.7.1/sonoff.bin) - NOTICE underscore as a dash is not supported in older versions
- Migrate to Tasmota 7.2.0 (http://ota.tasmota.com/tasmota/release-7.2.0/tasmota.bin)
--- Major change in parameter storage layout ---
- Migrate to Tasmota 8.5.1 (http://ota.tasmota.com/tasmota/release-8.5.1/tasmota.bin)
--- Major change in internal GPIO function representation ---
- Migrate to Tasmota 9.1 (http://ota.tasmota.com/tasmota/release-9.1.0/tasmota.bin.gz)
- Upgrade to latest release (http://ota.tasmota.com/tasmota/release/tasmota.bin.gz)
While fallback or downgrading is common practice it was never supported due to Settings additions or changes in newer releases. Starting with release v9.1.0 Imogen the internal GPIO function representation has changed in such a way that fallback is only possible to the latest GPIO configuration before installing v9.1.0.
Supported Core versions
This release will be supported from ESP8266/Arduino library Core version 2.7.7 due to reported security and stability issues on previous Core version. This will also support gzipped binaries.
This release will be supported from ESP32/Arduino library Core version 3.0.4.
Support of ESP8266 Core versions before 2.7.7 and ESP32 Core versions before 3.0.4 have been removed.
Known issues with v14.2.0
Due to the change from ESP32 Arduino Core2/IDF4 to Arduino Core3/IDF5 not all functionality has been restored. The following features are known not to work on ESP32:
- Wifi Range Extender #21200
Support of TLS
In addition to TLS using fingerprints now also user supplied CA certs, AWS IoT and Azure IoT is supported. Read full documentation
Initial configuration tools
For initial configuration this release supports Webserver based WifiManager or Serial based command interface.
Initial installation
Easy initial installation of Tasmota can be performed using the Tasmota WebInstaller.
Provided Binary Downloads
ESP8266 or ESP8285 based
The following binary downloads have been compiled with ESP8266/Arduino library core version 2.7.7.
- tasmota.bin = The Tasmota version with most drivers for 1M+ flash. RECOMMENDED RELEASE BINARY
- tasmota-4M.bin = The Tasmota version with most drivers and filesystem for 4M+ flash.
- tasmota-AD.bin to tasmota-VN.bin = The Tasmota version in different languages for 1M+ flash.
- tasmota-lite.bin = The Lite version without most drivers and sensors for 1M+ flash.
- tasmota-knx.bin = The Knx version without some features but adds KNX support for 1M+ flash.
- tasmota-sensors.bin = The Sensors version adds more useful sensors for 1M+ flash.
- tasmota-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 1M+ flash.
- tasmota-display.bin = The Display version without Energy Monitoring but adds display support for 1M+ flash.
- tasmota-zbbridge.bin = The dedicated Sonoff Zigbee Bridge version for 2M+ flash.
- tasmota-zigbee.bin = The dedicated cc25xx Zigbee Bridge version for 4M+ flash.
Above binaries are also available as gzipped version allowing faster uploads.
Latest released binaries can be downloaded from
- https://github.com/arendst/Tasmota-firmware/tree/firmware/release-firmware
- http://ota.tasmota.com/tasmota/release
Historical binaries can be downloaded from
The latter links can be used for OTA upgrades too like OtaUrl http://ota.tasmota.com/tasmota/release/tasmota.bin.gz
ESP32, ESP32-C2, ESP32-C3, ESP32-C6, ESP32-S2 and ESP32-S3 based
The following binary downloads have been compiled with ESP32/Arduino library core version 3.0.4.
- tasmota32.bin = The Tasmota version with most drivers including additional sensors and KNX for 4M+ flash. RECOMMENDED RELEASE BINARY
- tasmota32solo1.bin = The Tasmota version with most drivers including additional sensors and KNX for single core ESP32 and 4M+ flash.
- tasmota32s2.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-S2 with serial and 4M+ flash.
- tasmota32s2cdc.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-S2 with serial over embedded USB CDC only and 4M+ flash.
- tasmota32s3.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-S3 with USB HWCDC and fallback to serial and 4M+ flash.
- tasmota32c2.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C2 with serial and 4M+ flash.
- tasmota32c3.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C2 with USB HWCDC and fallback to serial and 4M+ flash.
- tasmota32c6.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C6 with USB HWCDC and fallback to serial and 4M+ flash.
- tasmota32-AD.bin to tasmota32-VN.bin = The Tasmota version in different languages for 4M+ flash.
- tasmota32-bluetooth.bin = The Bluetooth version adds BLE support for 4M+ flash.
- tasmota32-display.bin = The Display version without Energy Monitoring but adds display support for 4M+ flash.
- tasmota32-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 4M+ flash.
- tasmota32-lvgl.bin = The LVGL version adds Light and Versatile Graphics Library (LVGL) display support for 4M+ flash.
- tasmota32-nspanel.bin = The Sonoff NSPanel Smart Scene Wall Switch version with HASPmota display support.
- tasmota32-webcam.bin = The Webcam version adds webcam support for 4M+ flash.
- tasmota32-zbbridgepro.bin - The Sonoff Zigbee Bridge Pro version with CC2652P firmware load support.
Latest released binaries can be downloaded from
- https://github.com/arendst/Tasmota-firmware/tree/firmware/release-firmware
- https://ota.tasmota.com/tasmota32/release
Historical binaries can be downloaded from
The latter links can be used for OTA upgrades too like OtaUrl https://ota.tasmota.com/tasmota32/release/tasmota32.bin
Additional information
List of embedded modules.
Complete list of available feature and sensors.
Changelog v14.2.0 Rita
Added
- Command
AdcGpio<gpio> <parameters>to better support ADC configuration - Support for QMP6988 temperature and pressure sensor
- Support for Sonoff WTS01 temperature sensor using SerialBridge in
SSerialMode 3 - Support for Sonoff iFan04-H using template #16402
- Support for Sonoff POWCT Ring #21131
- Support for Wooliis Hall Effect Coulometer or Battery capacity monitor #21732
- Analog GPIO
ADC InputwithAdcGpio<pin> <start_range>,<end_range>,<margin>,1provide direct light control - Analog GPIO
ADC VoltagewithAdcGpio<pin> <start_range>,<end_range>,<lowest_voltage>,<highest_voltage>provide energy monitoring with dc voltage - Analog GPIO
ADC CurrentwithAdcGpio<pin> <start_range>,<end_range>,<lowest_current>,<highest_current>provide energy monitoring with dc voltage - Rule and Scripter xdrv sensor polling
- Skip MQTT response if command is prefixed with underscore #21740
- Skip MQTT response if commands are executed prefixed with
Backlog2(no delay) orBacklog3#21740 - Extend command
SetOption147 1to disable publish of IRReceived MQTT messages #21574 - NeoPool command
NPSetOption<x>to enabled/disable data validation/connection statistics #21850 - NeoPool data validation and communication statistics default enabled for ESP32 only #21721
- ESP32 support for power and energy limit checks, like
MaxEnergy2per phase #21695 - Berry solidification of
bytesinstances #21558 - Berry automatic rounding of float to int when calling C mapped functions #21601
- Berr...
Tasmota v14.1.0 Rachel
RELEASE NOTES
Migration Information
This version removes support for direct migration from versions before v8.1.0 (Doris)
See migration path for instructions how to migrate to a major version.
Do not upgrade from minimal to minimal version. It will most likely fail at some point and will require flashing via serial. If you do have to use minimal versions, always OTA to a full version of the same release before applying next minimal version.
Pay attention to the following version breaks due to dynamic settings updates:
- Migrate to Sonoff-Tasmota 3.9.x
- Migrate to Sonoff-Tasmota 4.x
- Migrate to Sonoff-Tasmota 5.14 (http://ota.tasmota.com/tasmota/release_5.14.0/sonoff.bin) - NOTICE underscore as a dash is not supported in older versions
- Migrate to Sonoff-Tasmota 6.7.1 (http://ota.tasmota.com/tasmota/release_6.7.1/sonoff.bin) - NOTICE underscore as a dash is not supported in older versions
- Migrate to Tasmota 7.2.0 (http://ota.tasmota.com/tasmota/release-7.2.0/tasmota.bin)
--- Major change in parameter storage layout ---
- Migrate to Tasmota 8.5.1 (http://ota.tasmota.com/tasmota/release-8.5.1/tasmota.bin)
--- Major change in internal GPIO function representation ---
- Migrate to Tasmota 9.1 (http://ota.tasmota.com/tasmota/release-9.1.0/tasmota.bin.gz)
- Upgrade to latest release (http://ota.tasmota.com/tasmota/release/tasmota.bin.gz)
While fallback or downgrading is common practice it was never supported due to Settings additions or changes in newer releases. Starting with release v9.1.0 Imogen the internal GPIO function representation has changed in such a way that fallback is only possible to the latest GPIO configuration before installing v9.1.0.
Supported Core versions
This release will be supported from ESP8266/Arduino library Core version 2.7.6 due to reported security and stability issues on previous Core version. This will also support gzipped binaries.
This release will be supported from ESP32/Arduino library Core version 3.0.0.
Support of ESP8266 Core versions before 2.7.6 and ESP32 Core versions before 3.0.0 have been removed.
Known issues with v14.1.0
Due to the change from ESP32 Arduino Core2/IDF4 to Arduino Core3/IDF5 not all functionality has been restored. The following features are known not to work on ESP32:
- Wifi Range Extender #21200
Support of TLS
In addition to TLS using fingerprints now also user supplied CA certs, AWS IoT and Azure IoT is supported. Read full documentation
Initial configuration tools
For initial configuration this release supports Webserver based WifiManager or Serial based command interface.
Initial installation
Easy initial installation of Tasmota can be performed using the Tasmota WebInstaller.
Provided Binary Downloads
ESP8266 or ESP8285 based
The following binary downloads have been compiled with ESP8266/Arduino library core version 2.7.6.
- tasmota.bin = The Tasmota version with most drivers for 1M+ flash. RECOMMENDED RELEASE BINARY
- tasmota-4M.bin = The Tasmota version with most drivers and filesystem for 4M+ flash.
- tasmota-AD.bin to tasmota-VN.bin = The Tasmota version in different languages for 1M+ flash.
- tasmota-lite.bin = The Lite version without most drivers and sensors for 1M+ flash.
- tasmota-knx.bin = The Knx version without some features but adds KNX support for 1M+ flash.
- tasmota-sensors.bin = The Sensors version adds more useful sensors for 1M+ flash.
- tasmota-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 1M+ flash.
- tasmota-display.bin = The Display version without Energy Monitoring but adds display support for 1M+ flash.
- tasmota-zbbridge.bin = The dedicated Sonoff Zigbee Bridge version for 2M+ flash.
- tasmota-zigbee.bin = The dedicated cc25xx Zigbee Bridge version for 4M+ flash.
Above binaries are also available as gzipped version allowing faster uploads.
Latest released binaries can be downloaded from
- https://github.com/arendst/Tasmota-firmware/tree/firmware/release-firmware
- http://ota.tasmota.com/tasmota/release
Historical binaries can be downloaded from
The latter links can be used for OTA upgrades too like OtaUrl http://ota.tasmota.com/tasmota/release/tasmota.bin.gz
ESP32, ESP32-C2, ESP32-C3, ESP32-C6, ESP32-S2 and ESP32-S3 based
The following binary downloads have been compiled with ESP32/Arduino library core version 3.0.0.
- tasmota32.bin = The Tasmota version with most drivers including additional sensors and KNX for 4M+ flash. RECOMMENDED RELEASE BINARY
- tasmota32solo1.bin = The Tasmota version with most drivers including additional sensors and KNX for single core ESP32 and 4M+ flash.
- tasmota32s2.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-S2 with serial and 4M+ flash.
- tasmota32s2cdc.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-S2 with serial over embedded USB CDC only and 4M+ flash.
- tasmota32s3.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-S3 with USB HWCDC and fallback to serial and 4M+ flash.
- tasmota32c2.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C2 with serial and 4M+ flash.
- tasmota32c3.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C2 with USB HWCDC and fallback to serial and 4M+ flash.
- tasmota32c6.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C6 with USB HWCDC and fallback to serial and 4M+ flash.
- tasmota32-AD.bin to tasmota32-VN.bin = The Tasmota version in different languages for 4M+ flash.
- tasmota32-bluetooth.bin = The Bluetooth version adds BLE support for 4M+ flash.
- tasmota32-display.bin = The Display version without Energy Monitoring but adds display support for 4M+ flash.
- tasmota32-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 4M+ flash.
- tasmota32-lvgl.bin = The LVGL version adds Light and Versatile Graphics Library (LVGL) display support for 4M+ flash.
- tasmota32-nspanel.bin = The Sonoff NSPanel Smart Scene Wall Switch version with HASPmota display support.
- tasmota32-webcam.bin = The Webcam version adds webcam support for 4M+ flash.
- tasmota32-zbbridgepro.bin - The Sonoff Zigbee Bridge Pro version with CC2652P firmware load support.
Latest released binaries can be downloaded from
- https://github.com/arendst/Tasmota-firmware/tree/firmware/release-firmware
- https://ota.tasmota.com/tasmota32/release
Historical binaries can be downloaded from
The latter links can be used for OTA upgrades too like OtaUrl https://ota.tasmota.com/tasmota32/release/tasmota32.bin
Additional information
List of embedded modules.
Complete list of available feature and sensors.
Changelog v14.1.0 Rachel
Added
- Optional command
WebRun(as WebQuery extension) #21364 - Support for Knx dimmer and color #21434
- SML FastExit for binary SML parsing #21497
- Berry add reuse of methods for interface-like code reuse #21500
- Support for Matter 1.3 Water leak detectors #21456
Changed
- ESP32 Core3 platform update from 2024.05.11 to 2024.05.13 #21524
- GPIOViewer from v1.5.2 to v1.5.4
- On universal display remove default backlight power if a PWM channel is used for backlight
- TCP bridge increased baudrate selection #21528
- Support W5500 SPI ethernet using four SPI GPIOs only without IRQ and RESET
- ESP32 compiler option from
target-aligntono-target-align#21407 - ESP32 I2S audio improvements #21433
- Berry binary compiled with gcc #21426
- Berry allow easy solidification of external Berry #21430
- Berry change internal storage of parent class for methods #21490
- Berry coc parser keeps order of variables #21542
Fixed
Tasmota v14.0.0 Rodney
RELEASE NOTES
Migration Information
This version removes support for direct migration from versions before v8.1.0 (Doris)
See migration path for instructions how to migrate to a major version.
Do not upgrade from minimal to minimal version. It will most likely fail at some point and will require flashing via serial. If you do have to use minimal versions, always OTA to a full version of the same release before applying next minimal version.
Pay attention to the following version breaks due to dynamic settings updates:
- Migrate to Sonoff-Tasmota 3.9.x
- Migrate to Sonoff-Tasmota 4.x
- Migrate to Sonoff-Tasmota 5.14 (http://ota.tasmota.com/tasmota/release_5.14.0/sonoff.bin) - NOTICE underscore as a dash is not supported in older versions
- Migrate to Sonoff-Tasmota 6.7.1 (http://ota.tasmota.com/tasmota/release_6.7.1/sonoff.bin) - NOTICE underscore as a dash is not supported in older versions
- Migrate to Tasmota 7.2.0 (http://ota.tasmota.com/tasmota/release-7.2.0/tasmota.bin)
--- Major change in parameter storage layout ---
- Migrate to Tasmota 8.5.1 (http://ota.tasmota.com/tasmota/release-8.5.1/tasmota.bin)
--- Major change in internal GPIO function representation ---
- Migrate to Tasmota 9.1 (http://ota.tasmota.com/tasmota/release-9.1.0/tasmota.bin.gz)
- Upgrade to latest release (http://ota.tasmota.com/tasmota/release/tasmota.bin.gz)
While fallback or downgrading is common practice it was never supported due to Settings additions or changes in newer releases. Starting with release v9.1.0 Imogen the internal GPIO function representation has changed in such a way that fallback is only possible to the latest GPIO configuration before installing v9.1.0.
Supported Core versions
This release will be supported from ESP8266/Arduino library Core version 2.7.6 due to reported security and stability issues on previous Core version. This will also support gzipped binaries.
This release will be supported from ESP32/Arduino library Core version 3.0.0.
Support of ESP8266 Core versions before 2.7.6 and ESP32 Core versions before 3.0.0 have been removed.
Known issues with v14.0.0
Due to the change from ESP32 Arduino Core2/IDF4 to Arduino Core3/IDF5 not all functionality has been restored. The following features are known not to work on ESP32:
- Wifi Range Extender #21200
Support of TLS
In addition to TLS using fingerprints now also user supplied CA certs, AWS IoT and Azure IoT is supported. Read full documentation
Initial configuration tools
For initial configuration this release supports Webserver based WifiManager or Serial based command interface.
Initial installation
Easy initial installation of Tasmota can be performed using the Tasmota WebInstaller.
Provided Binary Downloads
ESP8266 or ESP8285 based
The following binary downloads have been compiled with ESP8266/Arduino library core version 2.7.6.
- tasmota.bin = The Tasmota version with most drivers for 1M+ flash. RECOMMENDED RELEASE BINARY
- tasmota-4M.bin = The Tasmota version with most drivers and filesystem for 4M+ flash.
- tasmota-AD.bin to tasmota-VN.bin = The Tasmota version in different languages for 1M+ flash.
- tasmota-lite.bin = The Lite version without most drivers and sensors for 1M+ flash.
- tasmota-knx.bin = The Knx version without some features but adds KNX support for 1M+ flash.
- tasmota-sensors.bin = The Sensors version adds more useful sensors for 1M+ flash.
- tasmota-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 1M+ flash.
- tasmota-display.bin = The Display version without Energy Monitoring but adds display support for 1M+ flash.
- tasmota-zbbridge.bin = The dedicated Sonoff Zigbee Bridge version for 2M+ flash.
- tasmota-zigbee.bin = The dedicated cc25xx Zigbee Bridge version for 4M+ flash.
Above binaries are also available as gzipped version allowing faster uploads.
Latest released binaries can be downloaded from
- https://github.com/arendst/Tasmota-firmware/tree/firmware/release-firmware
- http://ota.tasmota.com/tasmota/release
Historical binaries can be downloaded from
The latter links can be used for OTA upgrades too like OtaUrl http://ota.tasmota.com/tasmota/release/tasmota.bin.gz
ESP32, ESP32-C2, ESP32-C3, ESP32-C6, ESP32-S2 and ESP32-S3 based
The following binary downloads have been compiled with ESP32/Arduino library core version 3.0.0.
- tasmota32.bin = The Tasmota version with most drivers including additional sensors and KNX for 4M+ flash. RECOMMENDED RELEASE BINARY
- tasmota32solo1.bin = The Tasmota version with most drivers including additional sensors and KNX for single core ESP32 and 4M+ flash.
- tasmota32s2.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-S2 with serial and 4M+ flash.
- tasmota32s2cdc.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-S2 with serial over embedded USB CDC only and 4M+ flash.
- tasmota32s3.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-S3 with USB HWCDC and fallback to serial and 4M+ flash.
- tasmota32c2.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C2 with serial and 4M+ flash.
- tasmota32c3.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C2 with USB HWCDC and fallback to serial and 4M+ flash.
- tasmota32c6.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C6 with USB HWCDC and fallback to serial and 4M+ flash.
- tasmota32-AD.bin to tasmota32-VN.bin = The Tasmota version in different languages for 4M+ flash.
- tasmota32-bluetooth.bin = The Bluetooth version adds BLE support for 4M+ flash.
- tasmota32-display.bin = The Display version without Energy Monitoring but adds display support for 4M+ flash.
- tasmota32-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 4M+ flash.
- tasmota32-lvgl.bin = The LVGL version adds Light and Versatile Graphics Library (LVGL) display support for 4M+ flash.
- tasmota32-nspanel.bin = The Sonoff NSPanel Smart Scene Wall Switch version with HASPmota display support.
- tasmota32-webcam.bin = The Webcam version adds webcam support for 4M+ flash.
- tasmota32-zbbridgepro.bin - The Sonoff Zigbee Bridge Pro version with CC2652P firmware load support.
Latest released binaries can be downloaded from
- https://github.com/arendst/Tasmota-firmware/tree/firmware/release-firmware
- https://ota.tasmota.com/tasmota32/release
Historical binaries can be downloaded from
The latter links can be used for OTA upgrades too like OtaUrl https://ota.tasmota.com/tasmota32/release/tasmota32.bin
Additional information
List of embedded modules.
Complete list of available feature and sensors.
Changelog v14.0.0 Rodney
Added
- PlatformIO target reset #21292
- Command
Wifi 6to enable 11ax on ESP32 - Command
PowerLockto disable power control of selected outputs #21081 - Command
Publish3to send binary data encoded as Hex, disabled in safeboot #21329 - Support for calculated heat index if temperature and humidity is available with
#define USE_HEAT_INDEX#4771 - Support for LoRa and single channel EU863-870 LoRaWanBridge #17790
- Support for AMS5915/AMS6915 temperature and pressure sensors #20814
- Support for LWT messages in TasMesh #20392
- Support IR data larger than 64 bits #20831
- Support for MCP23S08 #20971
- Support for ESP32-S3 120Mhz #20973
- Support Azure iothub direct method #21013
- Support for Domoticz non-persistent
DzIdx5toDzIdx32and disabling DOMOTICZ_OUT_TOPIC subscribe using commandDzIdx0 0#21019 - Support SPI GPIO configuration for Universal Touch Screen #21025
- Support for SPL06_007 pressure and temperature sensor #21185
- Support for AHT30 Temperature and Humidity Sensor #19922
- Support for compile time hostname with
#define WIFI_DEFAULT_HOSTNAME(#21236)#21236 - GPIOViewer pin mode support
- Zigbee support for attributes of type
uint48used by energy monitoring #20992 - QMC5...
Tasmota v13.4.0 Quinta
RELEASE NOTES
Migration Information
This version removes support for direct migration from versions before v8.1.0 (Doris)
See migration path for instructions how to migrate to a major version.
Do not upgrade from minimal to minimal version. It will most likely fail at some point and will require flashing via serial. If you do have to use minimal versions, always OTA to a full version of the same release before applying next minimal version.
Pay attention to the following version breaks due to dynamic settings updates:
- Migrate to Sonoff-Tasmota 3.9.x
- Migrate to Sonoff-Tasmota 4.x
- Migrate to Sonoff-Tasmota 5.14 (http://ota.tasmota.com/tasmota/release_5.14.0/sonoff.bin) - NOTICE underscore as a dash is not supported in older versions
- Migrate to Sonoff-Tasmota 6.7.1 (http://ota.tasmota.com/tasmota/release_6.7.1/sonoff.bin) - NOTICE underscore as a dash is not supported in older versions
- Migrate to Tasmota 7.2.0 (http://ota.tasmota.com/tasmota/release-7.2.0/tasmota.bin)
--- Major change in parameter storage layout ---
- Migrate to Tasmota 8.5.1 (http://ota.tasmota.com/tasmota/release-8.5.1/tasmota.bin)
--- Major change in internal GPIO function representation ---
- Migrate to Tasmota 9.1 (http://ota.tasmota.com/tasmota/release-9.1.0/tasmota.bin.gz)
- Upgrade to latest release (http://ota.tasmota.com/tasmota/release/tasmota.bin.gz)
While fallback or downgrading is common practice it was never supported due to Settings additions or changes in newer releases. Starting with release v9.1.0 Imogen the internal GPIO function representation has changed in such a way that fallback is only possible to the latest GPIO configuration before installing v9.1.0.
Supported Core versions
This release will be supported from ESP8266/Arduino library Core version 2.7.6 due to reported security and stability issues on previous Core version. This will also support gzipped binaries.
This release will be supported from ESP32/Arduino library Core version 2.0.14.
Support of ESP8266 Core versions before 2.7.6 and ESP32 Core versions before 2.0.14 have been removed.
Support of TLS
In addition to TLS using fingerprints now also user supplied CA certs, AWS IoT and Azure IoT is supported. Read full documentation
Initial configuration tools
For initial configuration this release supports Webserver based WifiManager or Serial based command interface.
Initial installation
Easy initial installation of Tasmota can be performed using the Tasmota WebInstaller.
Provided Binary Downloads
ESP8266 or ESP8285 based
The following binary downloads have been compiled with ESP8266/Arduino library core version 2.7.6.
- tasmota.bin = The Tasmota version with most drivers for 1M+ flash. RECOMMENDED RELEASE BINARY
- tasmota-4M.bin = The Tasmota version with most drivers and filesystem for 4M+ flash.
- tasmota-AD.bin to tasmota-VN.bin = The Tasmota version in different languages for 1M+ flash.
- tasmota-lite.bin = The Lite version without most drivers and sensors for 1M+ flash.
- tasmota-knx.bin = The Knx version without some features but adds KNX support for 1M+ flash.
- tasmota-sensors.bin = The Sensors version adds more useful sensors for 1M+ flash.
- tasmota-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 1M+ flash.
- tasmota-display.bin = The Display version without Energy Monitoring but adds display support for 1M+ flash.
- tasmota-zbbridge.bin = The dedicated Sonoff Zigbee Bridge version for 2M+ flash.
- tasmota-zigbee.bin = The dedicated cc25xx Zigbee Bridge version for 4M+ flash.
Above binaries are also available as gzipped version allowing faster uploads.
Latest released binaries can be downloaded from
- https://github.com/arendst/Tasmota-firmware/tree/main/release-firmware
- http://ota.tasmota.com/tasmota/release
Historical binaries can be downloaded from
The latter links can be used for OTA upgrades too like OtaUrl http://ota.tasmota.com/tasmota/release/tasmota.bin.gz
ESP32, ESP32-C3, ESP32-S2 and ESP32-S3 based
The following binary downloads have been compiled with ESP32/Arduino library core version 2.0.14.
- tasmota32.bin = The Tasmota version with most drivers including additional sensors and KNX for 4M+ flash. RECOMMENDED RELEASE BINARY
- tasmota32xy.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C3/S2/S3 and 4M+ flash.
- tasmota32xycdc.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C3/S2/S3 with serial over embedded USB CDC only and 4M+ flash.
- tasmota32solo1.bin = The Tasmota version with most drivers including additional sensors and KNX for single core ESP32 and 4M+ flash.
- tasmota32-AD.bin to tasmota32-VN.bin = The Tasmota version in different languages for 4M+ flash.
- tasmota32-bluetooth.bin = The Bluetooth version adds BLE support for 4M+ flash.
- tasmota32-display.bin = The Display version without Energy Monitoring but adds display support for 4M+ flash.
- tasmota32-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 4M+ flash.
- tasmota32-lvgl.bin = The LVGL version adds Light and Versatile Graphics Library (LVGL) display support for 4M+ flash.
- tasmota32-nspanel.bin = The Sonoff NSPanel Smart Scene Wall Switch version with HASPmota display support.
- tasmota32-webcam.bin = The Webcam version adds webcam support for 4M+ flash.
- tasmota32-zbbridgepro.bin - The Sonoff Zigbee Bridge Pro version with CC2652P firmware load support.
ESP32-C2 and ESP32-C6 based
The following binary downloads have been compiled with ESP32/Arduino library core version 3.0.0-alpha3.
- tasmota32c2-arduino30.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C2 and 4M+ flash.
- tasmota32c6cdc-arduino30.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C6 with serial over embedded USB CDC or hardware USB and 4M+ flash.
Latest released binaries can be downloaded from
- https://github.com/arendst/Tasmota-firmware/tree/main/release-firmware
- https://ota.tasmota.com/tasmota32/release
Historical binaries can be downloaded from
The latter links can be used for OTA upgrades too like OtaUrl https://ota.tasmota.com/tasmota32/release/tasmota32.bin
Additional information
List of embedded modules.
Complete list of available feature and sensors.
Changelog v13.4.0 Quinta
Added
- Command
TimedPower<index> <milliseconds>[,ON|OFF|TOGGLE|BLINK]executesPower<index> [ON|OFF|TOGGLE|BLINK]and after executesPower<index> [OFF|ON|TOGGLE|OFF] - Command
SetOption158 1to disable publish of ModbusReceived MQTT messages #20678 - Command
SetOption159 1to enable counting on both rising and falling edge #20712 - Display of active drivers using command
status 4 - GPIO Viewer to see realtime GPIO states using assets from
https://ota.tasmota.com/tasmota/gpioviewer/gpio_viewer_13_4_0/v2.0.8 - Support for CST816S touch interface #20213
- Support for Sonoff Basic R4 Magic Switch #20247
- Support negative power on BL0942 using index 5..8 #20322
- Support for pipsolar inverter #20408
- Support for HardwareSerial invert #15461
- NeoPool hydrolysis FL1 and Redox flag #20258
- SML support for IM350 #20474
- GUI sensor separators #20495
- ESP32 used UART information
- ESP32 support GPIOViewer when
define USE_ESP32_GPIO_VIEWERis enabled - ESP32 MI BLE support for Xiaomi LYWSD02MMC #20381
- ESP32 support for Shelly Plus Add-On using DS18x20 or DHT11/AM2301/DHT21/DHT22/AM2302/AM2321/SI7021 on GPIO0/1 #20580
- ESP32 MI32 Legacy initial support for sensors using BTHOME packet format #20625
- ESP32 Core3 support for SPI ethernet on DM9051, W5500 and KSZ8851
- ESP32-C3 support for GPIO11 #18350
- Berry GPIO viewer initial version using async webserver #20416
- Berry
introspect.set()for class attributes #20339 - Berry support for
tcpclientasyncintcpserver#20401 - Berry
tasmota.urlbecload(url:string) -> bool#20412 - Berry
gpio.read_pwmand `gpio.read_pwm_resolutio...
Tasmota v13.3.0 Quinlan
RELEASE NOTES
Migration Information
This version removes support for direct migration from versions before v8.1.0 (Doris)
See migration path for instructions how to migrate to a major version.
Do not upgrade from minimal to minimal version. It will most likely fail at some point and will require flashing via serial. If you do have to use minimal versions, always OTA to a full version of the same release before applying next minimal version.
Pay attention to the following version breaks due to dynamic settings updates:
- Migrate to Sonoff-Tasmota 3.9.x
- Migrate to Sonoff-Tasmota 4.x
- Migrate to Sonoff-Tasmota 5.14 (http://ota.tasmota.com/tasmota/release_5.14.0/sonoff.bin) - NOTICE underscore as a dash is not supported in older versions
- Migrate to Sonoff-Tasmota 6.7.1 (http://ota.tasmota.com/tasmota/release_6.7.1/sonoff.bin) - NOTICE underscore as a dash is not supported in older versions
- Migrate to Tasmota 7.2.0 (http://ota.tasmota.com/tasmota/release-7.2.0/tasmota.bin)
--- Major change in parameter storage layout ---
- Migrate to Tasmota 8.5.1 (http://ota.tasmota.com/tasmota/release-8.5.1/tasmota.bin)
--- Major change in internal GPIO function representation ---
- Migrate to Tasmota 9.1 (http://ota.tasmota.com/tasmota/release-9.1.0/tasmota.bin.gz)
- Upgrade to latest release (http://ota.tasmota.com/tasmota/release/tasmota.bin.gz)
While fallback or downgrading is common practice it was never supported due to Settings additions or changes in newer releases. Starting with release v9.1.0 Imogen the internal GPIO function representation has changed in such a way that fallback is only possible to the latest GPIO configuration before installing v9.1.0.
Supported Core versions
This release will be supported from ESP8266/Arduino library Core version 2.7.4.9 due to reported security and stability issues on previous Core version. This will also support gzipped binaries.
This release will be supported from ESP32/Arduino library Core version 2.0.14.
Support of ESP8266 Core versions before 2.7.4.9 and ESP32 Core versions before 2.0.14 have been removed.
Support of TLS
In addition to TLS using fingerprints now also user supplied CA certs, AWS IoT and Azure IoT is supported. Read full documentation
Initial configuration tools
For initial configuration this release supports Webserver based WifiManager or Serial based command interface.
Initial installation
Easy initial installation of Tasmota can be performed using the Tasmota WebInstaller.
Provided Binary Downloads
ESP8266 or ESP8285 based
The following binary downloads have been compiled with ESP8266/Arduino library core version 2.7.4.9.
- tasmota.bin = The Tasmota version with most drivers for 1M+ flash. RECOMMENDED RELEASE BINARY
- tasmota-4M.bin = The Tasmota version with most drivers and filesystem for 4M+ flash.
- tasmota-AD.bin to tasmota-VN.bin = The Tasmota version in different languages for 1M+ flash.
- tasmota-lite.bin = The Lite version without most drivers and sensors for 1M+ flash.
- tasmota-knx.bin = The Knx version without some features but adds KNX support for 1M+ flash.
- tasmota-sensors.bin = The Sensors version adds more useful sensors for 1M+ flash.
- tasmota-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 1M+ flash.
- tasmota-display.bin = The Display version without Energy Monitoring but adds display support for 1M+ flash.
- tasmota-zbbridge.bin = The dedicated Sonoff Zigbee Bridge version for 2M+ flash.
- tasmota-zigbee.bin = The dedicated cc25xx Zigbee Bridge version for 4M+ flash.
Above binaries are also available as gzipped version allowing faster uploads.
Latest released binaries can be downloaded from
- https://github.com/arendst/Tasmota-firmware/tree/main/release-firmware
- http://ota.tasmota.com/tasmota/release
Historical binaries can be downloaded from
The latter links can be used for OTA upgrades too like OtaUrl http://ota.tasmota.com/tasmota/release/tasmota.bin.gz
ESP32, ESP32-C3, ESP32-S2 and ESP32-S3 based
The following binary downloads have been compiled with ESP32/Arduino library core version 2.0.14.
- tasmota32.bin = The Tasmota version with most drivers including additional sensors and KNX for 4M+ flash. RECOMMENDED RELEASE BINARY
- tasmota32xy.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C3/S2/S3 and 4M+ flash.
- tasmota32xycdc.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C3/S2/S3 with serial over embedded USB CDC only and 4M+ flash.
- tasmota32solo1.bin = The Tasmota version with most drivers including additional sensors and KNX for single core ESP32 and 4M+ flash.
- tasmota32-AD.bin to tasmota32-VN.bin = The Tasmota version in different languages for 4M+ flash.
- tasmota32-bluetooth.bin = The Bluetooth version adds BLE support for 4M+ flash.
- tasmota32-display.bin = The Display version without Energy Monitoring but adds display support for 4M+ flash.
- tasmota32-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 4M+ flash.
- tasmota32-lvgl.bin = The LVGL version adds Light and Versatile Graphics Library (LVGL) display support for 4M+ flash.
- tasmota32-nspanel.bin = The Sonoff NSPanel Smart Scene Wall Switch version with HASPmota display support.
- tasmota32-webcam.bin = The Webcam version adds webcam support for 4M+ flash.
- tasmota32-zbbridgepro.bin - The Sonoff Zigbee Bridge Pro version with CC2652P firmware load support.
ESP32-C2 and ESP32-C6 based
The following binary downloads have been compiled with ESP32/Arduino library core version 3.0.0-alpha3.
- tasmota32c2-arduino30.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C2 and 4M+ flash.
- tasmota32c6cdc-arduino30.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C6 with serial over embedded USB CDC or hardware USB and 4M+ flash.
Latest released binaries can be downloaded from
- https://github.com/arendst/Tasmota-firmware/tree/main/release-firmware
- https://ota.tasmota.com/tasmota32/release
Historical binaries can be downloaded from
The latter links can be used for OTA upgrades too like OtaUrl https://ota.tasmota.com/tasmota32/release/tasmota32.bin
Additional information
List of embedded modules.
Complete list of available feature and sensors.
Changelog v13.3.0 Quinlan
Added
- Support for ESP32-C2 and ESP32-C6 using Arduino Core3
- Command
GpioReadto show input state #19810 - Command
WebCanvas linear-gradient(#F02 7%,#F93,#FF4,#082,#00F,#708 93%)to set GUI canvas - I2C bus2 support to iAQ core sensor #19799
- I2C bus2 support to HTU temperature and humidity sensor
- I2C bus2 support to BH1750 ambient light sensor
- I2C bus2 support to ADS1115 A/D Converter
- I2C bus2 support to SHTxX temperature and humidity sensor
- I2C bus2 support to HYTxxx temperature and humidity sensor
- I2C bus2 support to SI1145/6/7 Ultra violet index and light sensor
- I2C bus2 support to LM75AD temperature sensor
- Support for Winsen XH03x dust particle sensors using USE_PMS5003 and PMS_MODEL_ZH03X #19850
- ST7735S display.ini for 1.44 inch 128x128 red SPI display #19862
- Scripter TCP client #19914
- NeoPool hydrolysis setpoint and max
- NeoPool command
NPFiltrationSpeedto set non-standard filtration type speed #19857 - NeoPool command
SetOption157to enable output of sensitive data #19857 - NeoPool command
NPBoost#19973 - NeoPool sensor delta trigger (command
NPTelePeriod) #19973 - NeoPool enhancements for HomeAssistant #19857
- NeoPool store settings on unified file system #19973
- DeepSleep support through TIMERS #20117
- ESP32 auto TasConsole USB or Serial connection for Core3 by @Staars
- ESP32 Partition Wizard can be loaded dynamically #19980
- ESP32 support for Avago Tech Bluetooth Buttons #20088
- Berry
debug.gcdebug()to enable GC debugging #19936 - Berry AES_CBC to crypto module #19964
- Berry
scale_int, equivalent ofscale_uintfor signed integers #20090 - HASPmota add styling properties [#19912](https://...
Contributors
Assets 168
Tasmota v13.2.0 Quincy
RELEASE NOTES
Migration Information
This version removes support for direct migration from versions before v8.1.0 (Doris)
See migration path for instructions how to migrate to a major version.
Do not upgrade from minimal to minimal version. It will most likely fail at some point and will require flashing via serial. If you do have to use minimal versions, always OTA to a full version of the same release before applying next minimal version.
Pay attention to the following version breaks due to dynamic settings updates:
- Migrate to Sonoff-Tasmota 3.9.x
- Migrate to Sonoff-Tasmota 4.x
- Migrate to Sonoff-Tasmota 5.14 (http://ota.tasmota.com/tasmota/release_5.14.0/sonoff.bin) - NOTICE underscore as a dash is not supported in older versions
- Migrate to Sonoff-Tasmota 6.7.1 (http://ota.tasmota.com/tasmota/release_6.7.1/sonoff.bin) - NOTICE underscore as a dash is not supported in older versions
- Migrate to Tasmota 7.2.0 (http://ota.tasmota.com/tasmota/release-7.2.0/tasmota.bin)
--- Major change in parameter storage layout ---
- Migrate to Tasmota 8.5.1 (http://ota.tasmota.com/tasmota/release-8.5.1/tasmota.bin)
--- Major change in internal GPIO function representation ---
- Migrate to Tasmota 9.1 (http://ota.tasmota.com/tasmota/release-9.1.0/tasmota.bin.gz)
- Upgrade to latest release (http://ota.tasmota.com/tasmota/release/tasmota.bin.gz)
While fallback or downgrading is common practice it was never supported due to Settings additions or changes in newer releases. Starting with release v9.1.0 Imogen the internal GPIO function representation has changed in such a way that fallback is only possible to the latest GPIO configuration before installing v9.1.0.
Supported Core versions
This release will be supported from ESP8266/Arduino library Core version 2.7.4.9 due to reported security and stability issues on previous Core version. This will also support gzipped binaries.
This release will be supported from ESP32/Arduino library Core version 2.0.14.
Support of ESP8266 Core versions before 2.7.4.9 and ESP32 Core versions before 2.0.14 have been removed.
Support of TLS
In addition to TLS using fingerprints now also user supplied CA certs, AWS IoT and Azure IoT is supported. Read full documentation
Initial configuration tools
For initial configuration this release supports Webserver based WifiManager or Serial based command interface.
Initial installation
Easy initial installation of Tasmota can be performed using the Tasmota WebInstaller.
Provided Binary Downloads
ESP8266 or ESP8285 based
The following binary downloads have been compiled with ESP8266/Arduino library core version 2.7.4.9.
- tasmota.bin = The Tasmota version with most drivers for 1M+ flash. RECOMMENDED RELEASE BINARY
- tasmota-4M.bin = The Tasmota version with most drivers and filesystem for 4M+ flash.
- tasmota-AD.bin to tasmota-VN.bin = The Tasmota version in different languages for 1M+ flash.
- tasmota-lite.bin = The Lite version without most drivers and sensors for 1M+ flash.
- tasmota-knx.bin = The Knx version without some features but adds KNX support for 1M+ flash.
- tasmota-sensors.bin = The Sensors version adds more useful sensors for 1M+ flash.
- tasmota-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 1M+ flash.
- tasmota-display.bin = The Display version without Energy Monitoring but adds display support for 1M+ flash.
- tasmota-zbbridge.bin = The dedicated Sonoff Zigbee Bridge version for 2M+ flash.
- tasmota-zigbee.bin = The dedicated cc25xx Zigbee Bridge version for 4M+ flash.
Above binaries are also available as gzipped version allowing faster uploads.
Latest released binaries can be downloaded from
- https://github.com/arendst/Tasmota-firmware/tree/main/release-firmware
- http://ota.tasmota.com/tasmota/release
Historical binaries can be downloaded from
The latter links can be used for OTA upgrades too like OtaUrl http://ota.tasmota.com/tasmota/release/tasmota.bin.gz
ESP32, ESP32-C3, ESP32-S2 and ESP32-S3 based
The following binary downloads have been compiled with ESP32/Arduino library core version 2.0.14.
- tasmota32.bin = The Tasmota version with most drivers including additional sensors and KNX for 4M+ flash. RECOMMENDED RELEASE BINARY
- tasmota32xy.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C3/S2/S3 and 4M+ flash.
- tasmota32xycdc.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C3/S2/S3 with serial over embedded USB CDC only and 4M+ flash.
- tasmota32solo1.bin = The Tasmota version with most drivers including additional sensors and KNX for single core ESP32 and 4M+ flash.
- tasmota32-AD.bin to tasmota32-VN.bin = The Tasmota version in different languages for 4M+ flash.
- tasmota32-bluetooth.bin = The Bluetooth version adds BLE support for 4M+ flash.
- tasmota32-display.bin = The Display version without Energy Monitoring but adds display support for 4M+ flash.
- tasmota32-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 4M+ flash.
- tasmota32-lvgl.bin = The LVGL version adds Light and Versatile Graphics Library (LVGL) display support for 4M+ flash.
- tasmota32-nspanel.bin = The Sonoff NSPanel Smart Scene Wall Switch version with HASPmota display support.
- tasmota32-webcam.bin = The Webcam version adds webcam support for 4M+ flash.
- tasmota32-zbbridgepro.bin - The Sonoff Zigbee Bridge Pro version with CC2652P firmware load support.
Latest released binaries can be downloaded from
- https://github.com/arendst/Tasmota-firmware/tree/main/release-firmware
- https://ota.tasmota.com/tasmota32/release
Historical binaries can be downloaded from
The latter links can be used for OTA upgrades too like OtaUrl https://ota.tasmota.com/tasmota32/release/tasmota32.bin
Additional information
List of embedded modules.
Complete list of available feature and sensors.
Changelog v13.2.0 Quincy
Added
- Experimental support for ESP32-C2 and ESP32-C6 using Arduino core v3
- Commands to allow setting of timeprop parameters #19310
- Command
Mi32Name#19619 - Variables
%power<1..28>%and%switch<1..28>%to rules #19331 - Support different baudrates on BL0942 energy monitor
- Support for Shelly PlusPMMini, Plus1Mini and Plus1PMMini
- Support for HDMI CEC protocol #19434
- Support for ENS16x (air quality) and ENS210 (temp & RH) sensors #19479
- Support for HC8 CO2 sensor #19714
- Support for non-persistent
WebButton17toWebButton32#19580 - ESP32 commands
Ds18RescanandDs18RetryRead#19700 - ESP32 support for influxdb access using https #19582
- Berry read and write Counters #19558
- Matter support for Virtual Devices controllable via Rules or Berry #19520
Breaking Changed
Sendmailupgraded to ESP-Mail-Client v3.4.9 from v1.2.0, using BearSSL instead of MbedTLS #19460- Removed support for Homekit in favour of Matter #19738
Changed
- ESP32 Framework (Arduino Core) from v2.0.11 to v2.0.14
- ESP32 LVGL library from v8.3.8 to v8.3.10 (no functional change)
- Display invert setting after tasmota start in uDisplay driver #19337
- Consolidate SGP40 and SGP41 into SGP4x driver #19560
- MAX31855/MAX6675 sensors driver support up to 6 #19329
- Teleinfo use Apparent Power as Active Power approximation #19756
- ESP32 LittleFS updated to version with grow option #19635
- ESP32 I2S audio preparation for Arduino Core v3 #19637
- ESP32 analog from
analogRead()to calibratedanalogReadMilliVolts()#19732
Fixed
Tasmota v13.1.0 Quentin
RELEASE NOTES
Migration Information
This version removes support for direct migration from versions before v8.1.0 (Doris)
See migration path for instructions how to migrate to a major version.
Do not upgrade from minimal to minimal version. It will most likely fail at some point and will require flashing via serial. If you do have to use minimal versions, always OTA to a full version of the same release before applying next minimal version.
Pay attention to the following version breaks due to dynamic settings updates:
- Migrate to Sonoff-Tasmota 3.9.x
- Migrate to Sonoff-Tasmota 4.x
- Migrate to Sonoff-Tasmota 5.14 (http://ota.tasmota.com/tasmota/release_5.14.0/sonoff.bin) - NOTICE underscore as a dash is not supported in older versions
- Migrate to Sonoff-Tasmota 6.7.1 (http://ota.tasmota.com/tasmota/release_6.7.1/sonoff.bin) - NOTICE underscore as a dash is not supported in older versions
- Migrate to Tasmota 7.2.0 (http://ota.tasmota.com/tasmota/release-7.2.0/tasmota.bin)
--- Major change in parameter storage layout ---
- Migrate to Tasmota 8.5.1 (http://ota.tasmota.com/tasmota/release-8.5.1/tasmota.bin)
--- Major change in internal GPIO function representation ---
- Migrate to Tasmota 9.1 (http://ota.tasmota.com/tasmota/release-9.1.0/tasmota.bin.gz)
- Upgrade to latest release (http://ota.tasmota.com/tasmota/release/tasmota.bin.gz)
While fallback or downgrading is common practice it was never supported due to Settings additions or changes in newer releases. Starting with release v9.1.0 Imogen the internal GPIO function representation has changed in such a way that fallback is only possible to the latest GPIO configuration before installing v9.1.0.
Supported Core versions
This release will be supported from ESP8266/Arduino library Core version 2.7.4.9 due to reported security and stability issues on previous Core version. This will also support gzipped binaries.
This release will be supported from ESP32/Arduino library Core version 2.0.11.
Support of ESP8266 Core versions before 2.7.4.9 and ESP32 Core versions before 2.0.11 have been removed.
Support of TLS
In addition to TLS using fingerprints now also user supplied CA certs, AWS IoT and Azure IoT is supported. Read full documentation
Initial configuration tools
For initial configuration this release supports Webserver based WifiManager or Serial based command interface.
Initial installation
Easy initial installation of Tasmota can be performed using the Tasmota WebInstaller.
Provided Binary Downloads
ESP8266 or ESP8285 based
The following binary downloads have been compiled with ESP8266/Arduino library core version 2.7.4.9.
- tasmota.bin = The Tasmota version with most drivers for 1M+ flash. RECOMMENDED RELEASE BINARY
- tasmota-4M.bin = The Tasmota version with most drivers and filesystem for 4M+ flash.
- tasmota-AD.bin to tasmota-VN.bin = The Tasmota version in different languages for 1M+ flash.
- tasmota-lite.bin = The Lite version without most drivers and sensors for 1M+ flash.
- tasmota-knx.bin = The Knx version without some features but adds KNX support for 1M+ flash.
- tasmota-sensors.bin = The Sensors version adds more useful sensors for 1M+ flash.
- tasmota-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 1M+ flash.
- tasmota-display.bin = The Display version without Energy Monitoring but adds display support for 1M+ flash.
- tasmota-zbbridge.bin = The dedicated Sonoff Zigbee Bridge version for 2M+ flash.
- tasmota-zigbee.bin = The dedicated cc25xx Zigbee Bridge version for 4M+ flash.
Above binaries are also available as gzipped version allowing faster uploads.
Latest released binaries can be downloaded from
- https://github.com/arendst/Tasmota-firmware/tree/main/release-firmware
- http://ota.tasmota.com/tasmota/release
Historical binaries can be downloaded from
The latter links can be used for OTA upgrades too like OtaUrl http://ota.tasmota.com/tasmota/release/tasmota.bin.gz
ESP32, ESP32-C3, ESP32-S2 and ESP32-S3 based
The following binary downloads have been compiled with ESP32/Arduino library core version 2.0.11.
- tasmota32.bin = The Tasmota version with most drivers including additional sensors and KNX for 4M+ flash. RECOMMENDED RELEASE BINARY
- tasmota32xy.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C3/S2/S3 and 4M+ flash.
- tasmota32xycdc.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C3/S2/S3 with serial over embedded USB CDC only and 4M+ flash.
- tasmota32solo1.bin = The Tasmota version with most drivers including additional sensors and KNX for single core ESP32 and 4M+ flash.
- tasmota32-AD.bin to tasmota32-VN.bin = The Tasmota version in different languages for 4M+ flash.
- tasmota32-bluetooth.bin = The Bluetooth version adds BLE support for 4M+ flash.
- tasmota32-display.bin = The Display version without Energy Monitoring but adds display support for 4M+ flash.
- tasmota32-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 4M+ flash.
- tasmota32-lvgl.bin = The LVGL version adds Light and Versatile Graphics Library (LVGL) display support for 4M+ flash.
- tasmota32-nspanel.bin = The Sonoff NSPanel Smart Scene Wall Switch version with HASPmota display support.
- tasmota32-webcam.bin = The Webcam version adds webcam support for 4M+ flash.
- tasmota32-zbbridgepro.bin - The Sonoff Zigbee Bridge Pro version with CC2652P firmware load support.
Latest released binaries can be downloaded from
- https://github.com/arendst/Tasmota-firmware/tree/main/release-firmware
- https://ota.tasmota.com/tasmota32/release
Historical binaries can be downloaded from
The latter links can be used for OTA upgrades too like OtaUrl https://ota.tasmota.com/tasmota32/release/tasmota32.bin
Additional information
List of embedded modules.
Complete list of available feature and sensors.
Changelog v13.1.0 Quentin
Added
- Command
BrRestartto restart the Berry VM (experimental) #19003 - Command
Delay -1to wait until next second #18984 - Command
Restart 9to save all changes and go into deepsleep waiting for a reset #19024 - Support for MAX17043 fuel-gauge systems Lipo batteries #18788
- Support for multiple PCA9685 with extended functionality #18805
- Support for SGP41 TVOC/NOx Sensor #18880
- Support for DeepSleep battery level percentage #19134
- Zigbee decode Aqara 0000/FF01 attribute 03 as Temperature #19210
- ESP32 prepare for Arduino Core v3 and esp-idf v5 #19264
- Berry
getgblperformance counter todebug.counters()#19070 - Berry
_classcan be used instatic varinitialization code #19088 - Berry
energy.update_total()to callEnergyUpdateTotal()from energy driver #19117 - Berry
tasmota.loglevel()andtasmota.rtc_utc()for faster performance #19152 - Berry metrics for memory allocation/deallocation/reallocation #19150
- Berry AES CCM decrypting in a single call to avoid any object allocation #19153
- Berry bytes
getandsetwork for 3 bytes values #19225 - Partition Wizard is now able to convert to safeboot from Shelly partition layout #19034
- Matter option to disable bridge mode #18992
- Matter mini-profiler #19075
- Matter support for fabric_filtered request (for Google compatibility) #19249
Breaking Changed
- Berry
bool( [] )andbool( {} )now evaluate asfalse#18986 - Berry
import strictnow detects useless expression without side effects #18997
Changed
- IRremoteESP8266 library from v2.8.5 to v2.8.6
- ESP32 Framework (Arduino Core) from v2.0.10 to v2.0.11
- ESP32 LVGL library from v8.3.7 to v8.3.8 (no functional change)
- Initial
DisplayModefrom 1 to 0 andDisplayDimmmerfrom 10% to 50% #19138 - Configuration backup and restore now supports
.xdrvsetXXXfiles ...
Tasmota v13.0.0 Qasim
RELEASE NOTES
Migration Information
This version removes support for direct migration from versions before v8.1.0 (Doris)
See migration path for instructions how to migrate to a major version.
Do not upgrade from minimal to minimal version. It will most likely fail at some point and will require flashing via serial. If you do have to use minimal versions, always OTA to a full version of the same release before applying next minimal version.
Pay attention to the following version breaks due to dynamic settings updates:
- Migrate to Sonoff-Tasmota 3.9.x
- Migrate to Sonoff-Tasmota 4.x
- Migrate to Sonoff-Tasmota 5.14 (http://ota.tasmota.com/tasmota/release_5.14.0/sonoff.bin) - NOTICE underscore as a dash is not supported in older versions
- Migrate to Sonoff-Tasmota 6.7.1 (http://ota.tasmota.com/tasmota/release_6.7.1/sonoff.bin) - NOTICE underscore as a dash is not supported in older versions
- Migrate to Tasmota 7.2.0 (http://ota.tasmota.com/tasmota/release-7.2.0/tasmota.bin)
--- Major change in parameter storage layout ---
- Migrate to Tasmota 8.5.1 (http://ota.tasmota.com/tasmota/release-8.5.1/tasmota.bin)
--- Major change in internal GPIO function representation ---
- Migrate to Tasmota 9.1 (http://ota.tasmota.com/tasmota/release-9.1.0/tasmota.bin.gz)
- Upgrade to latest release (http://ota.tasmota.com/tasmota/release/tasmota.bin.gz)
While fallback or downgrading is common practice it was never supported due to Settings additions or changes in newer releases. Starting with release v9.1.0 Imogen the internal GPIO function representation has changed in such a way that fallback is only possible to the latest GPIO configuration before installing v9.1.0.
Supported Core versions
This release will be supported from ESP8266/Arduino library Core version 2.7.4.9 due to reported security and stability issues on previous Core version. This will also support gzipped binaries.
This release will be supported from ESP32/Arduino library Core version 2.0.10.
Support of ESP8266 Core versions before 2.7.4.9 and ESP32 Core versions before 2.0.10 have been removed.
Support of TLS
In addition to TLS using fingerprints now also user supplied CA certs, AWS IoT and Azure IoT is supported. Read full documentation
Initial configuration tools
For initial configuration this release supports Webserver based WifiManager or Serial based command interface.
Initial installation
Easy initial installation of Tasmota can be performed using the Tasmota WebInstaller.
Provided Binary Downloads
ESP8266 or ESP8285 based
The following binary downloads have been compiled with ESP8266/Arduino library core version 2.7.4.9.
- tasmota.bin = The Tasmota version with most drivers for 1M+ flash. RECOMMENDED RELEASE BINARY
- tasmota-4M.bin = The Tasmota version with most drivers and filesystem for 4M+ flash.
- tasmota-AD.bin to tasmota-VN.bin = The Tasmota version in different languages for 1M+ flash.
- tasmota-lite.bin = The Lite version without most drivers and sensors for 1M+ flash.
- tasmota-knx.bin = The Knx version without some features but adds KNX support for 1M+ flash.
- tasmota-sensors.bin = The Sensors version adds more useful sensors for 1M+ flash.
- tasmota-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 1M+ flash.
- tasmota-display.bin = The Display version without Energy Monitoring but adds display support for 1M+ flash.
- tasmota-zbbridge.bin = The dedicated Sonoff Zigbee Bridge version for 2M+ flash.
- tasmota-zigbee.bin = The dedicated cc25xx Zigbee Bridge version for 4M+ flash.
Above binaries are also available as gzipped version allowing faster uploads.
Latest released binaries can be downloaded from
- https://github.com/arendst/Tasmota-firmware/tree/main/release-firmware
- http://ota.tasmota.com/tasmota/release
Historical binaries can be downloaded from
The latter links can be used for OTA upgrades too like OtaUrl http://ota.tasmota.com/tasmota/release/tasmota.bin.gz
ESP32, ESP32-C3, ESP32-S2 and ESP32-S3 based
The following binary downloads have been compiled with ESP32/Arduino library core version 2.0.10.
- tasmota32.bin = The Tasmota version with most drivers including additional sensors and KNX for 4M+ flash. RECOMMENDED RELEASE BINARY
- tasmota32xy.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C3/S2/S3 and 4M+ flash.
- tasmota32xycdc.bin = The Tasmota version with most drivers including additional sensors and KNX for ESP32-C3/S2/S3 with serial over embedded USB CDC only and 4M+ flash.
- tasmota32solo1.bin = The Tasmota version with most drivers including additional sensors and KNX for single core ESP32 and 4M+ flash.
- tasmota32-AD.bin to tasmota32-VN.bin = The Tasmota version in different languages for 4M+ flash.
- tasmota32-bluetooth.bin = The Bluetooth version adds BLE support for 4M+ flash.
- tasmota32-display.bin = The Display version without Energy Monitoring but adds display support for 4M+ flash.
- tasmota32-ir.bin = The InfraRed Receiver and transmitter version allowing all available protocols provided by library IRremoteESP8266 but without most other features for 4M+ flash.
- tasmota32-lvgl.bin = The LVGL version adds Light and Versatile Graphics Library (LVGL) display support for 4M+ flash.
- tasmota32-nspanel.bin = The Sonoff NSPanel Smart Scene Wall Switch version with HASPmota display support.
- tasmota32-webcam.bin = The Webcam version adds webcam support for 4M+ flash.
- tasmota32-zbbridgepro.bin - The Sonoff Zigbee Bridge Pro version with CC2652P firmware load support.
Latest released binaries can be downloaded from
- https://github.com/arendst/Tasmota-firmware/tree/main/release-firmware
- https://ota.tasmota.com/tasmota32/release
Historical binaries can be downloaded from
The latter links can be used for OTA upgrades too like OtaUrl https://ota.tasmota.com/tasmota32/release/tasmota32.bin
Additional information
List of embedded modules.
Complete list of available feature and sensors.
Changelog v13.0.0 Qasim
Added
- Command
SetOption152 0/1to select two (0 = default) pin bistable or one (1) pin latching relay control #18386 - Command
I2cScan0to scan both busses on ESP32 with one command - Command
WifiPower 0to enable dynamic wifi power based on RSSI by @TD-er #15443 - Command
WifiPower 1to restore default wifi power - Support for TC74 temperature sensor by Michael Loftis #18042
- Support for GM861 1D and 2D bar code reader #18399
- Support for PCA9557 8-bit I/O expander #18632
- Display descriptor for ST7735 128x160 display #18741
- Zigbee support for air sensors #18665
- Zigbee firmware for Sonoff-ZB-Pro v20230507 #18968
- ESP32 command
Shuttersetupfor "Shelly 2.5 pro" automatic calibration and setup (experimental) - ESP32 Enhanced Shutterbuttons functionality to control tilt position, additionally incr/decr possible to position and tilt.
- Berry RS256 crypto algorithm (RSASSA-MCKS1_v1-5 with SHA256) used for JWT #18763
- Berry
tcpclientasyncclass for non-blocking TCP client - Berry
set_lsb_justified(bool)toAudioOutputI2S#18774 - Berry
string.format()now automatically converts type according to format #18890 - Berry global function
formatas a simpler syntax tostring.format#18925 - Berry f-strings as an alternative to string formatting #18937
- Berry Walrus operator ':=' #18963
- HASPmota
metaattribute and improvedberry_run#18685 - Matter sensors Humidity, Pressure, Illuminance #18441
- Matter allow
Matter#Initializedrule once the device is configured #18451 - Matter UI to change endpoints configuration #18498
- Matter support for Shutters with Tilt #18509
- Matter support for async HTTP used for bridged devices and remote relays #18656
- Matter bridge for ESP8266 remote endpoints (experimental) #18734
- Matter support for Occupancy via Switch (experimental) #18742
- Matter ability to add or remove endpoint in bridge mode (code only...
