-
-
Notifications
You must be signed in to change notification settings - Fork 64
/
smcroute.conf
61 lines (55 loc) · 2.72 KB
/
smcroute.conf
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
#
# smcroute.conf example
#
# The configuration file supports joining multicast groups, to use
# Layer-2 signaling so that switches and routers open up multicast
# traffic to your interfaces. Leave is not supported, remove the
# mgroup and SIGHUP your daemon, or send a specific leave command.
#
# NOTE: Use of the mgroup command should be avoided if possible.
# Instead configure "router ports" or similar on the switches
# or bridges on your LAN. This to have them direct all the
# multicast to your router, or select groups if they have
# such capabilities. Usually MAC multicast filters exist.
#
# Some switch manufacturers support mrdisc, RFC4286, which
# SMCRoute can use to advertise itself on source interfaces.
# If availble, use that instead of mgroup.
#
# Similarly supported is setting mroutes. Removing mroutes is not
# supported, remove/comment out the mroute from the .conf file, or
# send a remove command with smcroutectl.
#
# Syntax:
# phyint IFNAME <enable|disable> [mrdisc] [ttl-threshold <1-255>]
# mgroup from IIF [source ADDR[/LEN]] group GROUP[/LEN]
# mroute from IIF [source ADDR[/LEN]] group GROUP[/LEN] to OIF [OIF ...]
# include /path/to/*.conf
# This example assumes smcrouted was started with the `-N` flag.
# Only enable interfaces required for inbound and outbound traffic.
phyint eth0 enable ttl-threshold 11
phyint eth1 enable ttl-threshold 3
phyint eth2 enable ttl-threshold 5
phyint virbr0 enable ttl-threshold 5
# Instruct the kernel to join the multicast group 225.1.2.3 on interface
# eth0. Then add an mroute of the same multicast stream, from the host
# 192.168.1.42 on interface eth0 and forward to eth1 and eth2.
mgroup from eth0 group 225.1.2.3
mroute from eth0 source 192.168.1.42 group 225.1.2.3 to eth1 eth2
# Similar example, but using source-specific group join
mgroup from virbr0 source 192.168.123.110 group 225.1.2.4
mroute from virbr0 source 192.168.123.110 group 225.1.2.4 to eth0
# Allow multicast for group 225.3.2.1, from ANY source, ingressing on
# interface eth0 to be forwarded to eth1 and eth2. When the kernel
# receives a frame from unknown multicast sender, it asks smcrouted who
# use this "template" to match against, if the ingressing interface and
# group matches, smcrouted installs an (S,G) route in the kernel MFC.
mgroup from eth0 group 225.3.2.1
mroute from eth0 group 225.3.2.1 to eth1 eth2
# The previous is an example of the (*,G) support. It is also possible
# to specify a range of such rules.
mgroup from eth0 group 225.0.0.0/24
mroute from eth0 group 225.0.0.0/24 to eth1 eth2
# Include any snippet in /etc/smcroute.d/, but please remember that
# all phyint statements must be read first.
include /etc/smcroute.d/*.conf