v1.6.0

[1.6.0] - 2024-06-28:

Main changes since 1.5.0
Tested Segger Embedded Studio Version: 8.10d
Tested IAR Embedded Workbench for RISC-V Version: 3.30.1

Known Issue:

• some IAR projects does not work properly when optimization level is increased

Changed:

• soc: reorganize the directory structure
• soc: hpm6750: declare get_frequency_for_source API for clock drver header file
• soc: update soc cmakelists to add b ext info
• soc: hpm6750: add feature for ioc pad ctrl setting issue
• soc: toolchains: gcc: correct LMA for NOLOAD sections
• soc: move eh_frame into separate section
• boards: hpm6750xxxx apply workaround for E00029.
• boards: change hpm5301evklite adc16 channel
• boards: board.h: adc16: add marco BOARD_APP_ADC16_HW_TRIG_SRC_CLK_NAME
• boards: adjust function position of adc pin initialization
• boards: hpm6300evk and hpm6e00evk: sdram use px07 as femc dqs pin
• boards: hpm6e00evk: rename init_sdram_pins to init_femc_pins
• boards: hpm6e00evk: change board i2c instance to I2C0
• drivers: can/mcan add parameter check for low-level bit timing.
• drivers: enet: add bitfield ENET0_RMII_TXCLK_SEL for hpm6300
• drivers: i2c: add DATACNT high byte process
• drivers: pwm: update HRPWM process
• drivers: spi: optimize reading speed for spi_read_data API
• drivers: spi: add set/get data phase format APIs for spi master
• drivers: spi: delete the spi startand operation APIs
• drivers: adc16: remove an unused member conv_duration from adc16_config_t
• drivers: enet: update for enet_interrupt_enable_t
• drivers: mcan reduce unnecessary register access in mcan_read_rxfifo.
• drivers: mtg: add calculate function param clock
• drivers: mtg: add several calculate functions
• drivers: mcan lookeup the mcan msg ram base via mcan_soc_msg_buf variable if the MSG_BUF is in AHB RAM.
• drivers: adc16: disable improvement logic of adc16 for continuous sampling maximum voltage
• drivers: mcan improve transmitter delay compensation setting logic.
• drivers: femc: rename data_width_in_byte to cmd_data_width
• drivers: femc: update ns2cycle() to align up
• drivers: common: add packed attribute
• drivers: femc: delete duplicate config
• drivers: mtg: change the default parameters to the low order filter
• drivers: adc16: add API adc16_set_seq_hw_trigger_enable()
• drivers: spi : convert enumeration return in that gets parameters APIs
• drivers: pwm: add fault recovery code.
• driver: pwm: change pwm trig time
• components: enet_phy: dp83867/rtl8211: move the macro definition RGMII to board-level CMakeLists.txt
• components: eeprom_emulation: Add ATTR_RAMFUNC for all function
• components: eeprom_emulation: add power-off protection mechanism.
• components: dma_mgr: add burst in fixed transfer size and swap feature
• components: spi: add full_duplex and half_duplex operating APIs
• components: spi: support 1 to 32 bits width transfer for nonblocking APIs
• components: usb: device: support iso transfer mult feature
• middleware: hpm_sdmmc add emmc sleep & wakeup function.
• middleware: tinyusb: ehci: support chain transfer
• middleware: threadx: add low power support
• middleware: cherryusb: update for advance descriptor
• middleware: hpm_sdmmc: optimized to support multiple cards
• middleware: cherryusb/tinyusb/usbx: enable suspend isr
• middleware: FreeRTOS: update to 202210.01 lts
• middleware: cherryusb: update to v1.3.0
• middleware: freertos: modify missed timer count num
• middleware: freertos: update IAR port file
• middleware: freertos: delete fence operations
• middleware: freertos: make the calculation more simple.
• middleware: hpm_sdmmc add cache control macro.
• middleware: hpm_sdmmc: improve the logic for detecting CMD23 support.
• middleware: freertos: add tickless stop mode support
• middleware: freertos: add user custom process function call
• middleware: hpm_mcl_v2: add hpm smc control.
• middleware: freertos: place xPortxxx to isr_vector section
• middleware: hpm_math: add dsp support for zcc
• middleware: microros: add zcc support
• middleware: rtos: asm adjustment for zcc toolchain
• middleware: hpm_mcl_v2: add pwm dead area compensation.
• middleware: hpm_mcl_v2: add dq axis decoupling function
• middleware: cherryusb: add macro USBH_USE_CUSTOM_ISR/USBD_USE_CUSTOM_ISR
• middleware: lvgl: upgrade to v9
• middleware: lvgl: rewrite the scissor.
• middleware: lvgl: upgrade allocate algorithm for draw_buf.
• samples: rdc: remove unused dac driver in sample
• samples: lwip/netxduo/modbus: add conditional compile for reference clock setting in RMII mode
• samples: audio_codec: common: change FIL_SEARCH_NUM from 10 to 20
• samples: dhyrstone: surpress build warnings
• samples: dhrystone Optimize performance.
• samples: coremark Optimize performance.
• samples: drivers: spi: interrupt: transmission optimization. The transmission will start after the configuration is completed.
• samples: adapt spi components to drive and move to the samples dir for spi sdcard samples
• samples: cherryusb: device: change descriptor string to HPMicro
• samples: cherryusb: device: use advanced descriptor to support high/full speed
• samples: rename jpeg to image
• samples: drivers: sdxc: sd_fatfs: add card hotplug support
• samples: cherryusb: host: usbnet: replace block to noblock for read terminal char
• samples: cherryusb: host: usbnet: decrease lwip MEM_SIZE
• samples: cherryusb: move host hid info print code to thread
• samples: audio_codec: refactoring code
• samples: spi: dma: SPI master transmission optimization
• samples: mtg: make the open_loop_trajectory sample more readable
• samples: drivers: adc16: add some misc optimization
• samples: drivers: adc16: add pwmv2 support
• samples: motor_ctrl: bldc_foc_hw: remove hardware control
• samples: drivers: mcan add tips for the usage of tdc.
• samples: vglite: update rtos config file to fit gptmr tickless mode
• samples: lwip/modus/netxduo: add a function call to get the enet default interrupt config
• samples: sdm: using pwm to provide clock for sdm sensor.
• samples: spi_components: half_duplex: updated to support 1 to 32bits width transfer
• samples: spi_components: full_duplex: updated to support 1 to 32bits width transfer
• samples: add freertos tickless stop mode sample
• samples: benchmark: update compile options for zcc
• samples: drivers: adc16: optimize the process logic of sequence and preemption
• samples: drivers: sei: device: tamagawa: update eeprom cmd
• samples: adc12: optimization for trigger mux and trigger frequency settings
• samples: sei: device: tamagawa: support EEPROM protocol
• samples: mcl: add pwm dead area compensation.
• samples: motor_ctrl: add dq axis decoupling function
• samples: cherryusb: move dual_port samples to dual_port folder
• samples: cherryusb: adapter to cherryusb v1.3.0
• samples: drivers: adc12/adc16/dac: support abort feature in interactive terminal
• samples: lwip: lwip_iperf: support abort feature to reselect the test mode
• samples: lwip: common: multiple: add definitions of remote ip addresses for iperf
• samples: motor_ctrl: bldc_lvlg_foc: add lvgl v8.3.5 for this demo
• samples: tinyusb: uac2: support full speed
• samples: power_mode_switch: update readme
• samples: cherryusb: uac2: change default samplerate order
• samples: bldc_foc: update bldc_foc_angle_align() for hardware loop
• cmake: toolchain: add ar option to remove timestamp
• cmake: toolchain: suppress output while querying spec
• cmake: lld: update link option for zcc
• cmake/scripts/soc: support b ext convertion to tools
• cmake: sdk_app_src_glob: modify to recursive

Fixed:

• soc: update USE_NONVECTOR_MODE defined used
• soc: initialize .fast_ram.* section
• soc: iar linker: fix safe stack init
• soc: add missing ptmr clock
• soc: hpm6880: fix get_frequency_for_i2s error
• soc: hpm6880: Modify the value of SPI_SOC_FIFO_DEPTH from 4 to 8. for hpm_soc_feature.h
• soc: toolchain: iar fix iar ram_stress issue in ram_debug build.
• boards: hpm5301evklite: fixed can't output work for gptmr samples such as pwm_generate
• drivers: enet: fix the clearing of DMA PBL setting
• drivers: dma: fix dma_clear_transfer_status() API
• drivers: sdxc Fix timeout calculation issue and DMA enabling logic.
• drivers: adc16: fix the logic of adc16_set_pmt_queue_enable() when the parameter enable is false
• drivers: mbox: fix error that BEIE can't be operated by interface
• drivers: spi: fixed assignment value error for spi_set_clock_phase and spi_set_clock_polarity APIs
• drivers: lcdc: fix ST and DMA_ST clear api.
• drivers: mipi_dsi: fix MIPI_DSI_FMT_RGB565 config.
• drivers: spi: fixed assignment error issue for enable/disable address phase APIs
• drivers: i2c: fix return value type of i2c_get_data_count()
• components: usb device/enet_phy: fix unwanted files in localize folder
• components: panle: fix panel timing.
• components: eeprom_emulation: demo flash crashed.
• middleware: cherryusb: ehci: delete timeout clear before give sem
• middleware: uC/OS-III: modify fpu context save&restore
• middleware: cherryusb: fix freertos enter/exit critical
• middleware: audio_codec: fix hpm_wav_decode() single channel pbuf data
• middleware: mclv2: fix andes toolchain compiler error.
• middleware: cherryusb: fix ehci_qh_pool init miss busid for v1.3.0
• middleware: lwip: apps: lwiperf: fix the bug of failing to restart iperf in TCP/UDP server mode
• middleware: tinyusb: fix _usbd_dev.speed error to support full speed
• middleware: hpm_mcl_v2: fix uncontrolled after large changes in motor speed.
• samples: dhyrstone: fi...

v1.5.0

[1.5.0] - 2024-03-29:

Main changes since 1.4.0

Tested Segger Embedded Studio Version: 7.32a
Tested IAR Embedded Workbench for RISC-V Version: 3.20.1

Known Issue:

• some IAR projects does not work properly when optimization level is increased

Changed:

• soc: iomux: update macro prefix in pmic_iomux and batt_iomux.
• soc: feature: change usb endpoint max number from 8 to 16
• soc: correct svd files and add subpart module list
• drivers: usb: change usb_phy_get_line_state() to external function
• drivers: qeiv2: update filter length setting
• drivers: adc12/adc16: add sanity check for sample cycle
• drivers: femc: add delay_cell_disable config option
• drivers: i2s: change fifo threshold parameter.
• drivers: i2c: replace and use the macro definition of hpm_soc_ip_feature.
• drivers: uart: supplementary description of uart_check_status API.
• components: enet_phy: lan8720/rtl8201/rtl8211: unify the default config with type bool
• components: enet_phy: remove unused included header file
• components: enet_phy: rtl8201/rtl8211: update register description
• components: dma_mgr: change isr handler from static to public
• middleware: tinyusb: host: use echi drivers
• middleware: tinyusb: rename CFG_TUSB_HOST_DEVICE_MAX to CFG_TUH_DEVICE_MAX
• middleware: tinyusb: update to v0.16
• middleware: rtthread-nano: use soc reset_handler and define MAIN_ENTRY as entry
• middleware: fatfs: tinyusb: adapter to tinyusb update
• middleware: threadx: use TX_TIMER_TICKS_PER_SECOND to config work ticks
• middleware: threadx: use samples tx_user.h
• middleware: uC/OS-III: enable sw interrupt in OSCtxSw/OSIntCtxSw
• middleware: ucos: ports: Added IAR portable layer for ucos.
• middleware: cherryusb/azure_rtos: add defined ICCRISCV for iar
• middleware: hpm_math: simplify libdsp path.
• middleware: cherryusb: update to v1.1.0
• middleware: rtthread-nano:halt cpu when exception occur.
• middleware: hpm_math: simplify libnn path.
• middleware: threadx: move frequently called function to ram.
• middleware: tinyusb: change endpoint number from 8 to 16
• middleware: usbx: change endpoint number from 8 to 16
• middleware: cherryusb: msc device: update to support multi lun and deinit
• middleware: eclipse_threadx: update license
• middleware: fatfs: tinyusb: add osal_task_delay() when use rtos wait
• middleware: tinyusb: update CMakeLists.txt and delete custom osal_task_delay()
• middleware: tinyusb: add debounce in port change isr
• samples: erpc: add middleware src use middleware CMakeLists.txt
• samples: multicore: core1: use board_init_core1() API
• samples: multicore: coremark: delete custom reset_handler and use app_main as MAIN_ENTRY
• samples: tinyusb: update samples to adapter tinyusb v0.16
• samples: usbx: host: delete unused hpm_usb_host.h
• samples: usb: delete CONFIG_USB_HOST set
• samples: lvgl_coremark: disable freqswitch_btn when coremark running
• samples: mono: move to driver directory.
• samples: freertos: change configMAX_PRIORITIES from 7 to 32
• samples: rtthread: delete unused macro RT_THREAD_PRIORITY_32
• samples: cherryusb: usbnet: decrease rtos stack config size
• samples: lwip: all: unify logs about IP information
• samples: lwip: lwip_https_server: remove an unused file
• samples: lwip: all: update DHCP progress logic
• samples: lwip: common: remove s_pxNetIf
• samples: lwip: adjust the directories of netconf.c/netcof.h
• samples: lwip: common: optimize speed for getting IP from DHCP server
• samples: lwip: rename common_lwip.c to common.c
• samples: lwip: common: adjust the call logic of netif_set_up/netif_set_down
• samples: lwip: common: change the time of invoking netif_user_notification
• samples: lwip: common: rename user_notification to netif_user_notification
• samples: lwip: adjust directory structures to be compatible with single and multiple network ports
• samples: use generate_ide_projects for new samples
• samples: cherryusb: device: cdc acm: reorganize directory structure
• samplse: gptmr: t_shape_accel_decel: modify the source address mode of DMA.
• samples: cherryusb: device: change readbuf size from 2048 to CDC_MAX_MPS
• samples: drivers: femc: update sdram dqs config
• samples: update app.yaml to use ip_feature
• samples: drivers: uart: change to app uart
• samples: audio_codec: update wm8960 I2S protocol.
• samples: drivers: cam: change cam sample to cam_dvp sample.
• samples: usbx: device: msc: decrease ram disk size to 16KB
• samples: cherryusb: msc device: update to support multi lun
• samples: driver: uart_lin: support LIN transceiver on board.
• samples: adc: temp: rename temp to adc16_temperature
• samples: bldc block: Compatible with both hall and qeiv2 peripherals.
• samples: motor_ctrl: Modify the value of pwm reload.
• samples: lwip: common: single/multiple: update the size passed into sys_mbox_new()
• samples: lwip: common: single/multiple: replace enet_get_link_status with netif_is_link_up
• samples: lwip: lwip_https_server: remove unused header file
• samples: lwip: rename macro TCP_XXX_PORT
• samples: lwip: add cmake flag for netconn/socket api
• samples: decode_wav: sd_fafts: update sd_choose_music.
• samples: power_mode_switch: maintain xpi0 clock on switching preset
• samples: dhrystone Change the optmization level to O3.
• samples: tinyusb: hid_generic_inout: delete redundant image
• samples: power_mode_switch: hpm67/hpm63: preserve femc clock at wait/stop mode
• samples: erpc: core1: use optimization -os
• samples: update uart_tamagawa to use software trig if TRGM not exist.
• samples: eeprom_emulation: reduce management area
• samples: sdxc: use block_size instead of 512
• samples: erpc: add -fno-exceptions compile option
• samples: tinyusb: disable debug log print
• boards: hpm5300evk and hpm6800evk: add delay after USB_PWR Pin init for power stable
• boards: hpm6750evkmini: modify gptmr pins.
• boards: hpm6200evk: modify gptmr pins.
• boards: hpm6200evk: modify the i2c pins.
• boards: hpm6750xxx: update sdram dqs config
• boards: hpm6800evk:pinmux Increase drive strength for sdxc pins
• boards: iomux: update macro prefix for pmic_iomux and batt_iomux.
• boards: rename board feature
• boards: update BOARD_APP_UART definition
• boards: rename console definitions
• boards: hpm5301evklite: update uart clock in board.c.
• boards: hpm6750evkmini: change BOARD_GPTMR_PWM_DMA_SRC definition.
• docs: samples: use glob in high level readme.
• docs: update top level readme.
• docs: netxduo: update sntp readme.
• docs: threadx: update threadx hello readme.
• docs: lwip: align pictures to the left
• docs: pip: add cmake doc dependency
• docs: add changelog to sphnix-doc.
• scripts: ses: generate asm after build by default.
• scripts: update linked project path logic.
• scripts: check_board_cap.py: check ip feature's availability
• cmake: remove CMP0116 setting.
• cmake&scripts: clarify the error caused by core1 compiling failure.
• scripts: ses/iar: use relpath in project file

Added:

• soc: hpm6360/hpm6750/hpm6800: add MAC-related definitions in OTP section
• soc: reset: add MAIN_ENTRY macro to custom define main entry
• soc: add hpm6850 and hpm6830 part.
• soc: soc_modules.list: add tamper drivers
• soc: Add IAR toolchain support.
• soc: add ip feature to soc_modules.list
• soc: add hpm_soc_ip_feature.h
• soc: driver: ppor: add reset hold operation APIs
• soc: clock_driver add the clock_get_divider API.
• soc: sysctl: add apis to control clock preservation
• soc: toolchains: gcc: ram linker: add ILM last address overflow check
• drivers: mcan Add timeout counter support.
• drivers: tamper: add tamper driver
• drivers: cam: add cam_update_buffer2 API
• drivers: opamp: Add user configuration code.
• drivers: lcdc: add stride for layer config.
• drivers: pdma: add pdma_blit_ex.
• drivers:pllctl add out-of-bound check in pllctl driver.
• components:uart_lin: add hpm_uart_lin_send_wakeup() API
• components: enet_phy: add LAN8720 driver
• components: enet_phy: add definition of enet_phy_link_status_t
• middleware: cherryusb: host: add dual port support
• middleware: cmsis_os2: adapter to rtthread wrapper
• middleware: cmsis_os2: update freertos files
• middleware: cmsis_os2: adapter to threadx wrapper
• middleware: cmsis_os2: adapter to ucOS-III wrapper
• middleware: hpm_sdmmc Add eMMC config partition API.
• middleware: cherryusb Add IAR toolchain support
• middleware: erpc Fix IAR RISC-V support issue
• middleware: tflm: add IAR riscv support in flatbuffer
• middleware: FreeRTOS: portable:Added IAR portable layer.
• middleware: segger_rtt Added EWRISCV support
• middleware: hpm_math Add nds_dsp library for IAR.
• middleware: lwip: cc: add PACK_STRUCT_XXX definitions for IAR platform
• middleware: uC/OS-III: enable plicsw in IAR asm code
• middleware: add tinyengine
• middleware: threadx: add support for gptmr.
• middleware: threadx: add profile support.
• middleware: add agile_modbus.
• middleware: add cherryrb.
• middleware: cherryusb Add missing swap32/swap16 implementation.
• middleware: hpm_mclv2: add block type drive motors
• middleware: cherryusb: fix usbh_core ep0 buffer index
• boards: hpm6200xxx and hpm6750xxx: add board_init_core1() API
• boards: add tamper feature and pins init
• boards: hpm5300evk: add board_init_console() declaration in board.h
• boards: hpm6750evk/hpm6750evk2: add board_dual_usb feature
• boards: openocd: add windows guide to *_all_in_one.cfg
• boards: openocd: soc: add reset_soc proc
• board:add pgpio configuration on hpm5301evklite
  ...

v1.4.0

[1.4.0] - 2023-12-29:

Main changes since 1.3.0

Tested Segger Embedded Studio Version: 7.32

Changed:

• soc: hpm5301: add hpm5301
• soc: hpm6880: add hpm6880
• soc: HPM6750: pcfg: update dcdc dcm mode config
• soc: clock driver: update clock_set_source_divider() and clock_get_source()
• boards: add hpm5301evklite
• boards: add hpm6800evk
• boards: update clock_set_source_divider() to use clk_src_t type param
• boards: hpm6750evkmini: use the same uart port as core1 for some samples.
• drivers: dao: update driver support new feature on hpm6800
• drivers: adc16: update comment about cal_avg_cfg in calibration
• drivers: qeiv2: change adc trigmux name x to 0 and y to 1
• drivers: femc: add overflow protect to time config
• drivers: mcan Enlarge the range of CAN_EVENT_ERROR.
• components: serial_nor: add subdirectory in cmakelists
• middleware: cherryusb: update to v0.10.2
• middleware: cherryusb: rename host and device isr
• middleware: FreeRTOS: xPortIsInsideInterrupt() using CSR_MSCRATCH
• middleware:hpm_sdmmc Enhanced all speed modes support for SD and eMMC.
• middleware: usbx: device: support chain transfer
• samples: cherryusb: host: rndis: integrate dhcp thread into ping thread for host rndis ping and iperf sample
• samples: adc: temp: add isr for temp out of thresholds
• samples: drivers: acmp: optimization for comparing input voltage
• samples: lwip: add DHCP macro definition in CMakeLists.txt
• samples: lwip_ptp: enable DHCP feature in PTP samples
• samples: drivers: qeiv2: update API for adc-qeiv2 pin initialization
• samples: bldc_foc: change adc buffer size from 40 words to 48 words
• samples: remove explicitly c++ standard setting.
• samples: driver: cam: set default cmake build type
• samples: lwip: update to Class C static IP adress
• samples: tinyuf2: remove unnecessary cache ops.
• samples: lwip: lwip_tcpecho_freertos: optimization for API call in a thread-safe way
• samples: lwip: lwip_ptp: v1: slave: update static ip
• samples: lwip: optimize DHCP enable logic
• samples: lwip: opts: adjust the allocation strategy of memory pool
• samples: lwip: lwip_iperf: adjust MEM_SIZE for saving memory consumption
• samples: lwip: lwip_tcpecho_multi_ports: update the second IP with C class
• samples: enet: optimization for PHY selections
• samples: dma: update uart rx circle transfer buffer size
• samples: drivers: sdxc/emmc Correct doc for emmc sample.
• cmake: sdk_link_libraries link libraries for supported tools.
• cmake: add project name for hpm_sdk sub directory.
• cmake: decouple CMAKE_BUILD_TYPE and linker script.
• cmake: ses: remove -Ox from gcc option list.
• cmake: set default c++ standard to c++11.
• Update CONFIG_HAS_xxx to HPMSOC_HAS_xxx.
• segger: enable all warnings.
• segger: release: release optimization level use cmakelist config
• scripts: ses: set intermediate dir in project file.
• docs: remove quick start guide from top level readme
• docs: change doc structure.

Added:

• soc: HPM5361: add trgm filter shift length feature
• soc & drivers: hpm5300: add DMAMUX_SOC_WRITEONLY and TRGM_SOC_HAS_DMAMUX_EN features
• drivers: lcb: add lcb driver.
• drivers: sdxc add more APIs for timing and power control.
• drivers: mipi_csi: add mipi csi.
• drivers: cam: add cam_stop_safely API
• components: usb: device: add dtd chain transfer
• components: panel: enable panel component.
• components: camera: ov5640: add mipi interface.
• middleware: rtthread-nano: add v3.1.5
• middleware: rtthread-nano: add FPU support.
• middleware: tinyusb: device: update to support chain transfer
• middleware: cherryusb: device: update to support chain transfer
• middleware: vglite: add 4.0.49.
• middleware: cherryusb: add USB_OSAL_WAITING_FOREVER for sem and mq use
• middleware: add hpm_mcl_v2
• middleware: lwip: add ptpd v1 & v2
• middleware: cmsis_os2: add source files.
• samples: mcl: add step motor.
• samples: lwip: lwip_ptp: v2: support IEEE1588 V2
• samples: cherryusb: add audio_v2_mic_speaker_rtthread sample
• samples: cherryusb: host: add hid and msc rtthread samples
• samples: cherryusb: host: usbnet: add support ec20 module sample.
• samples: cmsis_os2: add blinky sample.
• samples: driver: mipi_csi: add mipi_csi.
• samples: mcan Support MCAN4-7 loopback testing.
• cmake: support custom output file name.

Fixed:

• soc: fix cache maintenance at startup
• soc: hpm53xx Correct exip API tree offset.
• soc: toolchain: missing .fast.* in gnu ld linker script.
• soc: fix tbss and tdata section not initialized.
• soc: sysctl: sysctl_enable_group_resource() should be check LOC_BUSY
• soc: hpm5300 Correct Cache size and Cacheline size.
• boards: hpm6750evkmini Fix the issue that eMMC is still 3.3V even 1.8V is selected.
• boards: hpm5301evklite correct jlink script device number.
• components: camera: power_up is enable by default for ov5640/ov7725.
• docs: samples: drivers: add numberic index.
• drivers/soc: fix build warning
• drivers: i2c: add slave device response judgment for master read/write APIs
• drivers: opamp: fix opamp vssa connect error.
• drivers: pllv2: fix pllctlv2_pll_is_stable() API
• drivers: qeiv2: fix invalid argument check
• drivers: dac: fix the upper limit value setting for DAC_OUTPUT
• drivers: jpeg: fix pixel format index for out buffer.
• drivers: uart: fix not support oversample 32 for rx idle detection on hpm5300
• middleware:ftafs Fix SD card init crash.
• middleware: mcl: fix path plan error.
• middleware: hpm_sdmmc Fix the issue that IO initialization work unstable on HPM6300.
• middleware: hpm_sdmmc Fix voltage switch setting issue for SD and eMMC.
• middleware: hpm_sdmmc Fix the PWR and VSEL IO initiaization issue. refs:hpm-sdk-#863
• samples: sei: fix nikon sample crc calc error.
• samples: cherryusb: msc device: add pre-format fat12 file system in u disk
• samples: adcx: replace const with a macro for ADC sample cycle
• samples: tinyusb:fix the usb host pin init.
• samples: motor_ctrl: bldc_littlevgl_foc: program crash.
• samples: qeiv2: uvw: fix uninitialized pointer usage
• samples: cherryusb: fix semaphore give in isr
• samples: drivers: Fix the issue that can error example may block.
• samples: uart_irq: fix unable to limit receive large than buffer size.
• samples: drivers:sdxc:emmc remove infinite loop for emmc initialization.
• samples: drivers: i2s: fix tx underflow during tx start
• samples: lwip: lwip_tcpecho_multiple_ports: fix no echo data when receiving large amounts of data
• samples: mcl: pwm duty set error.
• samples: cherryusb: host: usbnet: fixed when performing a stress test with a large amount of iperf data, will send fai.
• samples: cherryusb: audio_v2_mic_speaker_rtthread: fix mic no voice problem
• samples: jpeg_decode: add delay after usb pins init for waiting power stable
• samples: hfi: hpm6750evk2: fix the motor shake.
• cmake: segger: remove workstation specific path info.
• cmake/soc: fix heap/stack size setting for andes toolchain.
• cmake: ses: correct device name for core1.

v1.3.0

[1.3.0] - 2023-09-28:

Main changes since 1.2.0

Tested Segger Embedded Studio Version: 7.32

Changed:

• boards: hpm6200evk/hpm6300evk: delete unwanted clock_ahb div set
• boards: hpm6750xxx: switch dcdc work mode to dcm mode
• docs: sdk: boards: hpm6750evk2: add pps pin information
• component: wm8960: support sysclk pre-divider
• components: serial_nor: add serial nor flash.
• openocd: probes: ft2232: remove trst and srst config.
• ip: cam：remove 0x5c MAX_WN_CYCLE register in regs.h
• driver: cam: remove invalid register
• drivers: i2s: update API
• drivers: adc: adc12/adc16: rename adc16_get_busywait to adc16_is_nonblocking_mode
• drivers: adc: adc12/adc16: update adcx_init API
• drivers: pllctrl: update pllctrl drivers
• drivers: spi : add spi enable and disable datamerge
• drivers: spi : add spi_set_address_len API
• drivers: pdgo Add missing APIs
• drivers: uart: update uart rx idle flag process and fifo control
• soc: delete_unnecessary_ppor_reset_bit_field
• soc: hpm_gpiom_soc_drv.h: delete gpiom_gpio_t soc name
• soc: delete DMA_SOC_BUS_NUM Macro
• soc: pcfg: update pcfg SCG_CTRL related drivers
• soc: hpm6750:startup Enable LMM1 clock before access to LMM1
• soc: gcc ld: add memory used size check
• middleware: cherryusb: update to v0.10.1
• middleware: guix: demo adapts to 800 * 480 resolution
• middleware: guix: improve demo display performance
• middleware: cherryusb: update for midi descriptor define
• middleware: cherryusb: update for midi
• samples: drivers: adc: adc12/adc16: speed optimization for oneshot reading
• samples: drivers: adc: adc12/adc16： update API call used for nonblocking judgement
• samples: drivers: adc: adc12/adc16: update API call related to blocking setting in oneshot mode
• samples: drivers: adc: adc12/adc16: reduce the input parameters of init_trigger_target function
• samples: drivers: adc: adc12/adc16: update init_oneshot_config
• samples: drivers: adc: adc12/adc16: optimization for clearing interrupt status
• samples: drivers: pwm: Add pwm clock jitter demo
• samples: cherryusb: hid host: separate mouse and keyboard urb
• samples: hrpwm: Add demo for updating hrpwm frequency
• samples: drivers:mcan Add CAN error handling and refined logic.
• samples: mbx: move dualcore mbx sample to multicore folder
• samples: cherryusb: update for v0.10.1
• samples: motor_ctrl: bldc smc: gcc toolcahin enable fpu.
• samples: lwip: lwip_tcpecho_freertos: optimization in a thread-safety way
• samples: qeo: update qeo abz frequency configuration
• samples: gptmr: add sent_signal sample.
• samples: lwip: lwip_ptp: remove the dependency on pps0 pinout
• samples: dma_manager: update for use dma_mgr_setup_channel()
• samples: drivers: gptmr: pwm_measure: support use dma
• samples: lwip: lwip_httpsrv/lwip_https_server: rename project names for uniform naming
• samples: multicore: lvgl_coremark: delete custom linker files and using andes toolchain
• samples: flash_algo: update device size.
• samples: cherryusb: host: hid: use ep_mps to fill urb

Added:

• cmake: ses: support specify custom openocd board cfg file.
• cmake: support specifying minimum sdk version in app.yaml.
• boards: add hpm5300evk
• components: eeprom_emulation: add hpm nor-flash support
• components: eeprom_emulation: add eeprom emulation component
• soc: add APIs for get or set sysctl resource status
• drivers: common: add HPM_ALIGN_DOWN and HPM_ALIGN_UP define
• drivers: adc: ad12/adc16: add adcx_set_blocking_read/adcx_set_nonblocking_read
• drivers: add encoder position driver
• drivers: lcdc: add enable/disable background in alpha blender.
• drivers: usb: add api to set dp/dm pin pulldown resistance
• drivers: spi: add spi_get_rx_fifo_valid_data_size and spi_get_tx_fifo_valid_data_size APIs
• drivers: spi: add directIO function APIs
• drivers: enet: add rx resume API
• drivers: adc16: add resolution setting in adc16_get_default_config API
• drivers:rtc Add rtc_get_timeval API.
• drivers:mcan Add mcan_transmit_via_txfifo_nonblocking API.
• drivers: usb: add usb_hcd_set_power_ctrl_polarity() API
• drivers: plb: add plb drivers
• drivers: linv2: add linv2 driver
• drivers: sei: add sei driver
• drivers: dmav2: add dmav2 driver
• drivers: qeo: add qeo driver
• drivers: qeiv2: add qeiv2 driver
• drivers: mmc: add mmc driver
• drivers: rdc: add rdc driver
• drivers: add opamp driver
• drivers: bgpr: add related APIs for bgpr
• middleware: FreeRTOS: add xPortIsInsideInterrupt() API
• middleware: threadx: add definition automatically when enable traceX
• middleware: freeRTOS: add use gptmr to generate interrupt
• middleware: hpm_mcl: add hfi
• samples: drivers: adc: adc12/adc16: add wdog feature
• samples: add opamp demo
• samples: cherryusb: rndis: host: add iperf sample.
• samples: cherryusb: rndis: host: add ping sample.
• samples: drivers: adc: adc12/adc16: add hw trigger configuration in sequence mode
• samples: eeprom_emulation: add eeprom emulation perf test sample
• samples: eeprom_emulation: add base api demo
• samples: tracex: add demo for traceX usage
• samples: cherryusb: add audio_v1_mic_speaker_midi sample
• samples: cherryusb: add midi device sample
• samples: drivers: sei: add sei samples
• samples: drivers: plb: add plb demo
• samples: drivers: mmc: add mmc demo
• samples: drivers: qeiv2: add qeiv2 demo
• samples: drivers: qeo: add qeo demo
• samples: drivers: dmav2: add dmav2 demo
• samples: drivers: linv2: add linv2 demo
• samples: drivers: rdc: add rdc demo
• samples: drivers: pdgo Add PDGO samples
• samples: drivers: ewdg Add EWDG sample
• samples: lwip: add a lwip_tcpecho_multi_ports sample
• samples: motor_ctrl: add hfi

Fixed:

• cmake: fix segger default heap and stack size config
• cmake: fix add_subdirectory_ifdef arg processing.
• doc: boards: hpm6300evk: fix acmp pin info.
• boards: hpm6750evkmini: fix board_init_rgb_pwm_pins() problem
• boards: hpm6200evk: fix BOARD_G_GPIO_CTRL defined in wrong position
• openocd: hpm6750-dual-core: fix expression warning.
• component: wm8960: fix clock tolerance process
• soc: toolchains: segger: block tls add with fixed order
• soc: toolchain: gcc: fix Thread-Local Storage problem
• soc: segger linker files: fix heap and ctors initialize
• soc: fix interrupt complete operation
• soc: pcfg: fix DCDC_PROT[OVERLOAD_LP] bit access
• soc: ip: adc12: fix ADC12 threshold setting
• soc: HPM6750: fix clock setting and frequency obatining error
• soc: HPM6360: fix clock source definitions for ADC16
• soc: HPM6280: fix clock source definitions for ADC16
• soc: HPM6360: fix obtaining clock source error for DAC
• soc: HPM6280: fix obtaining clock source for DAC
• drivers: adc16: add bus mode enable control APIs
• drivers: adc16: fix ahb setting
• drivers: cam: clear the status of CAM should not affect other bits
• drivers: trgmux: filter function can't work.
• drivers: src: adc16: fix end count setting
• drivers: adc/dac: fix interrupt status clearing
• drivers: adc16: fix DMA access format
• drivers: sdm: fix over sample rate and signal sync problem
• drivers: pwm: fix pwm xcmp enable setting
• drivers: pwm: correct external fault polarity setting.
• drivers: pwm: add update hrpwm reload shadow api
• drivers: spi: fix can't set change data_bits use spi_set_data_bits API
• drivers: ptpc: fix ptpc_clear_irq_status API issue.
• drivers: i2c: fix i2c_clear_status API issue.
• drivers: gptmr: fix gptmr_clear_status API issue.
• middleware: erpc: rpmsg_lite: fix platform_in_isr() error
• middleware:hpm_sdmmc Fix the issue sdsc cards are not supported.
• middleware: threadx: fix D extend asm code error
• samples: usbx: add multi devices and hot plug support
• samples: motor_ctrl: fix adc trig invalidate.
• samples: lwip: fix TCP reception error when size over 2KB
• samples: lwip: DHCP failure in lwip_tcpecho_freertos
• samples: drivers: adc: adc12: fix the status flag judgement in isr process
• samples: rgb_led: fix cmp shadow error
• samples: gptmr: pwm_generate: fix inaccurate duty in high frequency
• samples: lwip: low_level_input: fix the network storm issue
• samples: timer_basic: fix inconsistent use of defines
• samples: drivers: adc: adc16: fix the bit of interrupt status clearing in sequence mode
• samples: power_mode_switch: trigger system lowpower for standby mode
• samples: touch_panel: fix error data when 5 fingers touch screen at same time.
• samples: jpeg: jpeg_decode: fixed lcd display is tore when decoder is running
• samples: jpeg: jpeg_decode: malloc out of memory on gcc
• samples: drivers:can Fix abnormal behavior on can error sample.
• samples: segger_rtt: call board_init_clock.
• samples: drivers: acmp: fix one toggle value but multi toggle pulses
• samples: lwip_tcpecho_freerstos: fix code stuck with gcc toolchain
• samples: jpeg: fix JPEG_USE_UDISK compile error
• samples: bldc_foc: fix input value range.
• samples: cherryusb: rndis: udp_echo: fix echo extra char
• samples: usbx: fix global var placement
• samples: power_mode_switch: set to preset_1 after exiting wait mode.
• samples: pla: fix pla first pulse abnormal.
• samples: plb: fix the first pulse is abnormal.

v1.2.0

[1.2.0] - 2023-06-30:

Main changes since 1.1.0

Tested Segger Embedded Studio Version: 7.22

Changed:

• boards: hpm6750evk*: decrease core frequency from 816MHz to 648MHz
• openocd: soc: hpm6280: simplify dual core release core1 approach.
• cmake: segger: configure optimization level according to gcc level.
• soc: dmamux: move it from ip to soc
• soc: interrupt: adjust irq api. #659
• soc: improve svd file
• soc: hpm_soc_feature.h: remove ADC16_SOC_TEMP_CH_EN for some specified Socs
• components: enet_phy: update the common enet phy header file
• components: sgtl5000 and wm8960: update clock setting
• drivers: uart: update uart driver
• drivers: pdma: improve quality of scale
• drivers: adc: adjust wait_dis type in adc16_config_t struct
• drivers: enet: update rmii reference clock setting API for ENET
• utils: hpm_swap: escape for andes toolchain.
• middleware: hpm_sdmmc: add spi sdcard
• middleware: motor_ctrl: change the file organization
• middleware: motor_ctrl: remove slide control content from foc
• middleware: lvgl: upgrade to v8.3.5 (with pdma)
• middleware: lvgl: Add direct mode
• middleware: cherryusb: update version to v0.8.0
• samples: I2S_DMA and I2S Interrupt: update sample behavior
• samples: cherryusb: hid host: separate mouse and keyboard urb
• samples: cherryusb: increase max interface and endpoint number Configuration
• samples: cherryusb: uac2: move setting sampling freq to isr
• samples: cherryusb: audio: update descriptor for identification
• samples: audio_codec: set codec voice to max and increase irq priority
• samples: multicore: lvgl_coremark: delete custom linker files and using andes toolchain
• samples: lvgl_audio_player: update CMakeLists.txt to using noncacheable framebuffer
• samples: spi: clean the redundant code
• samples: i2c: improve the processing of FIFO in ISR
• samples: drivers: uart: update uart_rx_timeout demo
• samples: drivers: gptmr: split sample into multiple function samples
• samples: drivers: adc: optimization for all macro definitions in applications
• samples: drivers: adc: update struct member names
• samples: update clock divider setting for ADC-related examples
• samples: cherryusb: move vid/pid etc definition to usb_config.h
• samples: cherryusb: device: update vid to hpmicro 0x34B7
• samples: cherryusb: change API update for v0.8
• samples: cherryusb: device: audiov1: change to full speed mode
• samples: tinyusb: uac2: update descriptor and sample
• samples: lwip: disable mmc interrupt settings
• samples: lwip: lwip_ptp: v1: sync precision improvement

Added:

• cmake: toolchains: add isa spec 20191213 support.
• cmake: ses: support set ses raw option in CMakeLists.txt
• cmake: add option to specify board search path.
• cmake: generate compile_commands.json file
• soc: hpm_soc_feature: add a common macro for ADC12 and ADC16
• drivers: cam: add new APIs
• drivers: spi: add new APIs
• drivers: i2c: add new APIs
• drivers: I2S: add i2s_check_data_line_status API
• drivers: dma: add dma_set_transfer_src_width_byte_size() API
• drivers: gptmr: add output capture APIs
• drivers: gptmr: add gptmr_channel_get_dma_request_event api
• drivers: adc: add adc16_trigger_pmt_by_sw API
• drivers: enet: add some APIs related to interrupt settings
• drivers: enet: add a new API for transmisstion
• drivers: usb: add macro CONFIG_USB_DEVICE_FS to set full speed mode
• components: uart_lin: add uart lin component
• components: add smbus
• components: add sccb
• middleware: lvgl: add macro HPM_LVGL_FRAMEBUFFER_NONCACHEABLE
• middleware: add AzureRTOS (threadx/usbx/netx/guix)
• middleware: hpm_mcl: sensorless over-zero
• middleware: add smc
• middleware: hpm_sdmmc Add eMMC support
• middleware: hpm_math: add bit conversion function
• middleware: add uC/OS-III
• middleware: cherryusb: audio: add feedback descriptor
• middleware: cherryusb: audio: add param to set endpoint bmAttributes
• middleware: microros: add microros foxy sources
• samples: drivers: spi: add spi_sdcard_fatfs sample
• samples: drivers: spi: add sd sample
• samples: add uart_lin
• samples: motor_ctrl: sensorless: over-zero demo
• samples: cherryusb: add rndis host dhcp samples
• samples: drivers: sdxc :emmc Added eMMC sample
• samples: drivers: adc12: update irq pattern for sequence usage
• samples: drivers: pla: add pla tamagawa demo
• samples: drivers: gptmr: add counter_sync sample
• samples: drivers: gptmr: add timer_basic sample
• samples: drivers: gptmr: add t_shape_accel_decel sample
• samples: drivers: dma/gptmr: add trigger dma transfer using gptmr event sample
• samples: drivers: uart add uart_rx_timeout sample
• samples: i2c: add smbus samples
• samples: lwip: lwip_tcpecho_freertos: add self-adaption
• samples: cherryusb: hid host: move usbh_submit_urb() out of condition
• samples: cherryusb: add composite freertos sample
• samples: cherryusb: add rndis freertos sample
• samples: cherryusb: add msc freertos sample
• samples: cherryusb: add audio v2 mic speaker freertos sample
• samples: cherryusb: add hid mouse freertos sample
• samples: cherryusb: add hid keyboard freertos sample
• samples: cherryusb: add cdc acm freertos sample
• samples: cherryusb: add rndis tcp server sample
• samples: cherryusb: add rndis device udp_echo sample
• samples: cherryusb: add rndis device http_server sample
• samples: cherryusb: device: add audio_v2_speaker_sync sample
• samples: add several uC/OS-III samples
• samples: smc: add smc demo
• samples: microros: add subscriber, sevice and publisher
• samples: uC/OS-III: mutex

Fixed:

• cmake: ses: fix __SEGGER_RTL_vfprintf issue with nds tool in SES 7.20.
• soc: hpm6280: Modify the number of PWM cmps.
• soc: reset.c: __dso_handle needs to be declared for nds toolchain.
• soc: fix max buffer length in sequence mode for ADC
• soc: HPM6750: enet soc drv: fix set clock delay settings
• soc:hpm6360:sdxc Correct clock divider settting issue
• drivers: pla: missing Union Field
• drivers: spi: fix the problem of CMD and ADDR configuration order
• drivers: i2c: fix clock frequency error rate problem
• drivers: i2c: clear CMPL bit in API to avoid blocking the trans
• drivers: i2c: fix i2c slave device read and write fail
• drivers: i2c: fix read data unexpected multi transition.
• drivers: i2c: fix w1c clear status error
• driver: usb: fix w1c clear flag error
• drivers: gptmr: fix dma request enum definition
• drivers: adc: fix logics for judging the validity of arguments
• component: uart_lin: fix break signal problem
• middleware: cherryusb: fix buffer size error
• middleware: lvgl: fix fbbuffer option
• samples: gptmr: fix pwm_measure sample compile waring
• samples: jpeg: fix interchange format of exif support
• samples: jpeg: fix jpeg decode
• samples: drivers: spi: fix the problem of CMD and ADDR configuration order
• samples: drivers: mcan: can_fd loopback test setting is incorrect
• samples: cherryusb: http_server_freertos: fix printf content error
• samples: cherryusb: audio: change endpoint attributes for support MACBOOK
• samples: tinyusb: msc: increase block numbers for windows format
• samples: lwip: lwip_httpsrv: fix reload or refresh error

v1.1.0

[1.1.0] - 2023-03-31:

Main changes since 1.0.0

Tested Segger Embedded Studio Version: 7.10

Changed:

• docs: add new docs for rtd project.
• soc: ip: enet: update the enet register file
• soc: ip: adc16: update the adc16 header file
• soc: hpm_romapi - Add APIs for configuring remapping, exip regions
• drivers: enet: improve APIs related to PPS
• drivers: adc: change adc bus blocking interface
• drivers: adc: optimize getting oneshot result
• drivers: src: update the default config for ADC12&ADC16
• boards: rename board-level APIs related to enet
• components: enet_phy: rtl8201: update the register file
• middleware: hpm_math: update dsp version
• middleware: erpc: update to v1.10.0
• samples: uart: rename uart_dma_rx_idle to uart_software_rx_idle
• samples: uart: add hardware rx idle detection sample
• samples: multicore: erpc: core1 add sdk_compile_options(-O1)
• samples: drivers: gptmr: update sample output.
• samples: lwip: common: arch: ethernetif: update a calling function name
• samples:drivers: adc: optimize oneshot handler

Added:

• arch: add FPU related APIs
• soc/board: add HPM6280 support
• soc: HPM6750: acmp: add ACMP section
• components: add mt9m114 support
• drivers: add raw8 pixel format support
• drivers: csr - Implement CSR driver
• drivers: adc: adc16: support resolution setting
• drivers/samples: add SDM/PLA/CRC/MCAN
• drivers: I2C: add new API
• drivers: adc: adc16: support resolution setting
• drivers: enet: add enet control config for transmission
• middleware: cherryusb: audio: update class driver and demo template
• middleware: add mbedtls lib files with SDP acceleration
• freeRTOS: add support for static allocation
• samples: drivers: enet: add a pps demo
• samples: cherryusb: add audio samples
• samples: add the resolution parameter in all demos with ADC16
• samples: add rfft demo
• sampels: i2c: add interrupt b2b samples
• samples: drivers: i2s: add an i2s_master demo
• samples: drivers: i2s: add an i2s_slave demo
• samples : rom_api : add sw_gm_api filter
• samples: add the resolution parameter in all demos with ADC16

Fixed:

• openocd: hpm6300evk: update sdram initialization.
• drivers: trgmux: trigmux edge filter setting error
• drivers: enet: fix register access error
• drivers: adc16: fix the config error of ADC16_CONFIG1
• drivers: i2c: fix i2c timing configuration
• drivers: SPI: fix SPI status API
• drivers: fix gptmr cmp value don't minus one
• drivers: mcan: correct the mcan ext_id filter issue
• drivers: I2C: fix issue in i2c_master_address_read API
• drivers: Self_ACK cannot be set in CAN driver
• drivers: rtc rtc_config_alarm always return error code
• cmake: correct source code compilation
• soc: toolchain: gcc: initialize heap for SES
• soc: gcc linker files: add NOLOAD keyword to noncacheable.bss section
• soc: HPM6360: gcc: ld: correct noncacheable region name.
• drivers: qei: Fix speed display always zero
• middleware: freertos: disable global irq before vTaskStartScheduler
• freeRTOS: fix trap when enable float feature
• freeRTOS: fix tick lost
• freeRTOS: fix segger project build warning
• samples: drivers: i2s: fix CFGR config
• samples: drivers: fix acmp toggle error
• samples: lwip: fix the DHCP issue
• samples: uart: fix irq_id judgment
• samples: fix the order of uart pin configuration and clock configuration
• samples: update spi dma sample
• samples: drivers: sysctl: correct reset enable approach.
• samples: fix dma_general_transfer sample memory out of bounds
• samples: drivers: wdog: Fix logic issue on finding the nearest interrupt interval
• sample: audio_codec: decoder_wav: add '\0' to fatfs path

v1.0.0

[1.00.0] - 2022-12-31:

Main changes since 0.14.0

Tested Segger Embedded Studio Version: 7.10

Changed:

• boards: add version info in banner.
• board: lcdc: move panel para to board
• components: spi component to support to transfer different width of data in dma handshake mode
• drivers: rename dram to femc
• middleware: cherryusb update to v0.7.0
• middleware: erpc: update for support rtos
• middleware: hpm_mcl: update api naming
• samples: erpc: rename erpc_matrix_multiply_rpmsg to erpc_matrix_multiply_rpmsg_bm
• samples: erpc: reorganize erpc_matrix_multiply_rpmsg samples
• samples: erpc: move samples folder to erpc_matrix_multiply_rpmsg
• samples: update i2c/spi dma channel and dmamux channel definition
• ses: project template: use demo.* as output file naming.
• soc: HPM6750: toolchains: update linker files
• soc: HPM6360: toolchains: update linker files

Added:

• arch: riscv: add read_clear_csr() API
• component: add wm8960 support
• component: add usb device iso transfer support
• drivers: hpm_common: include hpm_sdk_version.h.
• drivers: common: add NOP and WFI.
• drivers: uart: add api to recv/send byte directly.
• soc: HPM6750 linker files: rename rpmsg_sh_mem to sh_mem
• cmake: add sdk version header file generation.
• middleware: tinyusb: add audio class
• middleware: hpm_math: add NN library
• samples: erpc: add erpc_two_way_rpc_rpmsg_rtos sample
• samples: erpc: add erpc_matrix_multiply_rpmsg_rtos sample
• samples: add power mode switch demo. #282
• samples: drivers: adc: add a temperature measurement demo
• samples: drviers: femc: add sram sample
• samples: lwip demo for FreeRTOS
• samples: lwip demo of interrupt usage
• samples: tinyusb: add uac2 demo
• samples: tflm: add face detection demo
• samples: tflm: add MLPerf Tiny benchmark demo
• samples: lwip: common: feature: add a LPI interrupt process

Fixed:

• drivers:interrupt: Fix FPU context crashing in nested irq case
• drivers: src: adc: fix adc result in period mode
• segger: update app directory structure in SES.
• soc: disable irq during cache maintenance
• middleware: lvgl: fps calculation to No.
• samples: get off level based on board api.
• samples: multicore: hello: core1 rgb led does not change correctly.