Skip to content

Latest commit

 

History

History
141 lines (94 loc) · 6.25 KB

README.md

File metadata and controls

141 lines (94 loc) · 6.25 KB
Raw

Nx_MDNS_wifi application description

This application demonstrates mDNS on Cypress module for the STM32H747I board.

It performs mDNS services announce and deannounce functions using the NetxDuo stack.

Expected success behavior

  • Application announces and deannounces various mDNS services and displays the same on the UART.

Error behaviors

None

Assumptions if any

  • The application is using the DHCP to acquire IP address, thus a DHCP server should be reachable by the board in the LAN used to test the application.

ThreadX usage hints

  • ThreadX uses the Systick as time base, thus it is mandatory that the HAL uses a separate time base through the TIM IPs.

  • ThreadX is configured with 1000 ticks/sec, this should be taken into account when using delays or timeouts at application. It is always possible to reconfigure it in the tx_user.h, the TX_TIMER_TICKS_PER_SECOND define, but this should be reflected in tx_initialize_low_level.S file too.

  • ThreadX is disabling all interrupts during kernel start-up to avoid any unexpected behavior, therefore all system related calls (HAL, BSP) should be done either at the beginning of the application or inside the thread entry functions.

  • ThreadX offers the tx_application_define() function, that is automatically called by the tx_kernel_enter() API. It is highly recommended to use it to create all applications ThreadX related resources (threads, semaphores, memory pools...) but it should not in any way contain a system API call (HAL or BSP).

  • Using dynamic memory allocation requires to apply some changes to the linker file. ThreadX needs to pass a pointer to the first free memory location in RAM to the tx_application_define() function, using the first_unused_memory argument. This requires changes in the linker files to expose this memory location.

    • For EWARM add the following section into the .icf file:
       place in RAM_region    { last section FREE_MEM };
    • For MDK-ARM: either define the RW_IRAM1 region in the ".sct" file or modify the line below in tx_initialize_low_level.S to match the memory region being used
        LDR r1, =|Image$$RW_IRAM1$$ZI$$Limit|
    • For STM32CubeIDE add the following section into the .ld file:
        ._threadx_heap :
    {
     . = ALIGN(8);
     __RAM_segment_used_end__ = .;
     . = . + 64K;
     . = ALIGN(8);
    } >RAM_D1 AT> RAM_D1

    The simplest way to provide memory for ThreadX is to define a new section, see ._threadx_heap above. In the example above the ThreadX heap size is set to 64KBytes. The ._threadx_heap must be located between the .bss and the ._user_heap_stack sections in the linker script. Caution: Make sure that ThreadX does not need more than the provided heap memory (64KBytes in this example). Read more in STM32CubeIDE User Guide, chapter: "Linker script".

    • The tx_initialize_low_level.S should be also modified to enable the USE_DYNAMIC_MEMORY_ALLOCATION compilation flag.

NetX Duo usage hints

For more details about the MPU configuration please refer to the AN4838

Keywords

RTOS, Network, ThreadX, NetXDuo, mDNS, WiFi, Station mode, microSD

Hardware and Software environment

  • This application runs on STM32H747xx devices.

  • This application has been tested with STMicroelectronics STM32H747I-DISCO boards Revision: MB1248-H747I-D02 and can be easily tailored to any other supported device and development board.

  • A daughter board with the WiFi module is to be plugged into the microSD card connector CN12 of the STM32H747I-DISCO board.

  • The daughter board that was used is made up of:

    • A Murata uSD-M.2 Adapter Kit rev A (J1 position 2-3, VBAT from microSD connector)
    • The 1DX M.2 Module for the Cypress WiFi (CYW4343W)

    Connect Pin 20 of STMod+ connector P2 of STM32H747I-DISCO to the uSD M.2 Adapter (J9 pin3 WL_REG_ON_HOST) that supports the Cypress device as described with the below pictures:

picture1

picture2

  • This application uses USART1 to provide a console for commands, the hyperterminal configuration is as follows:

    • BaudRate = 115200 baud
    • Word Length = 8 Bits
    • Stop Bit = 1
    • Parity = None
    • Flow control = None
    • Line endings set to LF (receive).

  • This application requires a WiFi access point to connect to:

    • With a transparent Internet connectivity: no proxy, no firewall blocking the outgoing traffic.
    • Running a DHCP server delivering the IP and DNS configuration to the board.

  • Development PC with the Bonjour SDK installed and connected to the same WiFi access point as the board.

    • This is used to verify the services being announced/deannounced.

How to use it ?

In order to make the program work, you must do the following:

  • Open your preferred toolchain

  • Edit the file CM7/Core/Inc/cy_wifi_conf.h to enter the name of your WiFi access point (WIFI_SSID) to connect to and its password (WIFI_PASSWORD).

  • For each target configuration (Nx_MDNS_wifi_CM4 first then Nx_MDNS_wifi_CM7) :

    • Rebuild all files
    • Load images into target memory

  • After loading the two images, you have to reset the board in order to boot (Cortex-M7) and CPU2 (Cortex-M4) at once.

  • Enter the following commands in a Command Prompt window (you may open multiple windows for each command) to verify the services being announced/deannounced:

    • C:\Windows\System32> dns-sd.exe -L test_announce _test_st local

    • C:\Windows\System32> dns-sd.exe -L test_announce1 _test_st local

    • C:\Windows\System32> dns-sd.exe -L test_announce2 _test_st local

    • C:\Windows\System32> dns-sd.exe -L test_announce3 _test_st local

    • C:\Windows\System32> dns-sd.exe -B _test_st local

  • Run the application

  • One can also ping the device using the hostname to verify the automatic IPv4 address resolved by mDNS:

    • C:\Windows\System32> ping.exe mDNS-HOST.local

  • Application announces and deannounces various mDNS services and displays the same on the UART.