-
Notifications
You must be signed in to change notification settings - Fork 3
/
Help.h
130 lines (128 loc) · 3.66 KB
/
Help.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
#ifndef _HELP_h
#define _HELP_h
const char help[] PROGMEM = ""
"<body>\n"
" <pre>\n"
" <h3>Commands</h3>\n"
" You can send commands from FHEM via the JeeLink module\n"
" Example: <i>set myJeeLink raw 2,120b</i>\n"
" or from the log page of the LGW frontend\n"
"\n"
" <u><b><n>a: Activity LED</b></u>\n"
" n=0: LED disabled\n"
" n=1: LED enabled\n"
"\n"
" <u><b><n,d>b: Alert using AddOn-buzzer</b></u>\n"
" n: beep sequence\n"
" d: duration\n"
" Examples:\n"
" 1,60b -> beep 60 seconds\n"
" 2,120b -> beep beep 120 seconds\n"
" 3,300b -> beep beep beep 300 seconds\n"
" 0b -> stop beep\n"
"\n"
" <u><b><n>c: data rate for transmit on RFM #1</b></u>\n"
" Used for CustomSensor\n"
"\n"
" <u><b><n>d: Debug-Messages</b></u>\n"
" n=1 will send debug messages to the serial port\n"
" Should never be used for normal operation\n"
"\n"
" <u><b>8266e: Erase EEPROM</b></u>\n"
" Will erase the configuration in the EEPROM\n"
" Is a kind of factory reset\n"
"\n"
" <u><b>8377e: Reboot</b></u>\n"
" Will reboot the LGW\n"
"\n"
" <u><b><n#r>f: Set frequency</b></u>\n"
" n: frequency in kHz\n"
" r: radio number (1...5)\n"
" Example: 868296#2f -> set Radio 2 to 868296 kHz\n"
"\n"
" <u><b>1g: Get the settings</b></u>\n"
" Send the current settigs to the serial port\n"
"\n"
" <u><b><n>h: Altitude</b></u>\n"
" n: altitude in meters above sea level\n"
" If a pressure transmitter is connected to the LGW the pressure will get normalized\n"
" for the passed altitude\n"
"\n"
" <u><b><n,f,p>i: Initialize PCA301</b></u>\n"
" n: Radio number that shall handle (exclusively) PCA301\n"
" f: frequency\n"
" p: poll interval\n"
" Example: 3,868950,120i will initialize radio 3 for PCA301 with 868950 kHz and 120 seconds poll interval\n"
"\n"
" <u><b><n#r>m: Data rate toggle mode</b></u>\n"
" n: toggle mode\n"
" bits 1: 17.241 kbps\n"
" 2: 9.579 kbps\n"
" 4: 8.842 kbps\n"
" 8: 20.000 kbps\n"
" r: radio number (1...5)\n"
" Example: 5#2m -> Radio 2 toggle 17.241 / 8.842\n"
"\n"
" <u><b><n>o: Reserved</b></u>\n"
"\n"
" <u><b><n>p: Pass payload mode</b></u>\n"
" Transmit the payload on the serial port\n"
" n: 1 = all\n"
" 2 = only undecoded data\n"
" Should never be used for normal operation\n"
"\n"
" <u><b><n#r>r: Set data rate</b></u>\n"
" n: data rate\n"
" 20000: EC3000\n"
" 17241: TX29, TX25, WS 1080, ...\n"
" 9579: TX35, 30.3155, ...\n"
" 8842: WS 1600\n"
" r: radio number (1...5)\n"
" Example: 9579#2r -> set Radio 2 to 9579 kbps\n"
"\n"
" <u><b><x,x,x,x>s: Send to PCA301</b></u>\n"
" Used by FHEM\n"
"\n"
" <u><b><x,x,x,x>S: Send to CustomSensor</b></u>\n"
" Sends the passed bytes to a CustomSensor\n"
"\n"
" <u><b><n#r>t: Set toggle interval</b></u>\n"
" n: interval in seconds\n"
" r: radio number (1...5)\n"
" Example: 30#2t -> set Radio 2 to 30 seconds toggle\n"
"\n"
" <u><b><n>u: ---</b></u>\n"
" Reserved\n"
"\n"
" <u><b>v: Show version</b></u>\n"
" Shows version and configuration info\n"
"\n"
" <u><b>0w: Disable WiFi</b></u>\n"
" Switches the WiFi off.\n"
" You can only switch it off, but not on.\n"
"\n"
" <u><b><n>x: ---</b></u>\n"
" Reserved\n"
"\n"
" <u><b><n>z: Analyze frames</b></u>\n"
" Shows raw sensor data and the decoded data in the frontend log\n"
" <n> is bit coded\n"
" 1: LaCrosse\n"
" 2: WS 1600\n"
" 4: WS 1080\n"
" 8: EMT7110\n"
" 16: LevelSender\n"
" 32: CustomSensor\n"
" 64: EC3000\n"
" 128: PCA301\n"
" Should never be used for normal operation\n"
"\n"
" </pre>\n"
"</body>\n"
"\n"
"\n"
"\n"
"\n"
"\n"
;
#endif