- 中文版本
- Basic Example:
ADF defines a series of common display patterns from a functional point of view. In different hardware environments, you can use the interface display_service_set_pattern to set display patterns. Currently, ADF allows you to drive LEDs with PWM, AW2013, IS3x, and WS2812.
This example demonstrates how to set LED mode and checks whether all LEDs are working properly. For more information, please refer to ADF Get Started.
This example runs on the boards that are marked with a green checkbox in the table. Please remember to select the board in menuconfig as discussed in Section Configuration below.
This example supports IDF release/v3.3 and later branches. By default, it runs on ADF's built-in branch $ADF_PATH/esp-idf.
The default board for this example is ESP32-Lyrat V4.3. If you need to run this example on other development boards, select the board in menuconfig, such as ESP32-Lyrat-Mini V1.1.
menuconfig > Audio HAL > ESP32-Lyrat-Mini V1.1Build the project and flash it to the board, then run monitor tool to view serial output (replace PORT with your board's serial port name):
idf.py -p PORT flash monitorTo exit the serial monitor, type Ctrl-].
See ESP-IDF Programming Guide for full steps to configure and build an ESP-IDF project.
After the example starts to run, the LEDs loop through different display patterns in order. The log is as follows:
rst:0x1 (POWERON_RESET),boot:0x1f (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:7204
load:0x40078000,len:13212
load:0x40080400,len:4568
0x40080400: _init at ??:?
entry 0x400806f4
I (27) boot: ESP-IDF v4.2.2-1-g379ca2123 2nd stage bootloader
I (27) boot: compile time 15:01:00
I (27) boot: chip revision: 3
I (31) boot_comm: chip revision: 3, min. bootloader chip revision: 0
I (38) boot.esp32: SPI Speed : 40MHz
I (43) boot.esp32: SPI Mode : DIO
I (47) boot.esp32: SPI Flash Size : 2MB
I (52) boot: Enabling RNG early entropy source...
I (57) boot: Partition Table:
I (61) boot: ## Label Usage Type ST Offset Length
I (68) boot: 0 nvs WiFi data 01 02 00009000 00006000
I (76) boot: 1 phy_init RF data 01 01 0000f000 00001000
I (83) boot: 2 factory factory app 00 00 00010000 00100000
I (91) boot: End of partition table
I (95) boot_comm: chip revision: 3, min. application chip revision: 0
I (102) esp_image: segment 0: paddr=0x00010020 vaddr=0x3f400020 size=0x06c00 ( 27648) map
I (122) esp_image: segment 1: paddr=0x00016c28 vaddr=0x3ffb0000 size=0x020ac ( 8364) load
I (125) esp_image: segment 2: paddr=0x00018cdc vaddr=0x40080000 size=0x0733c ( 29500) load
0x40080000: _WindowOverflow4 at /hengyongchao/esp-idfs/esp-idf-v4.2.2-psram/components/freertos/xtensa/xtensa_vectors.S:1730
I (142) esp_image: segment 3: paddr=0x00020020 vaddr=0x400d0020 size=0x16d48 ( 93512) map
0x400d0020: _stext at ??:?
I (178) esp_image: segment 4: paddr=0x00036d70 vaddr=0x4008733c size=0x03118 ( 12568) load
0x4008733c: xthal_window_spill_nw at /Users/igrokhotkov/e/esp32/hal/hal/windowspill_asm.S:212
I (189) boot: Loaded app from partition at offset 0x10000
I (189) boot: Disabling RNG early entropy source...
I (190) cpu_start: Pro cpu up.
I (193) cpu_start: Application information:
I (198) cpu_start: Project name: check_display_led
I (204) cpu_start: App version: v2.2-228-g07116fa5-dirty
I (210) cpu_start: Compile time: Nov 12 2021 16:20:42
I (217) cpu_start: ELF file SHA256: b5d39a251613418c...
I (223) cpu_start: ESP-IDF: v4.2.2-1-g379ca2123
I (229) cpu_start: Starting app cpu, entry point is 0x40081618
0x40081618: call_start_cpu1 at /hengyongchao/esp-idfs/esp-idf-v4.2.2-psram/components/esp32/cpu_start.c:287
I (0) cpu_start: App cpu up.
I (239) heap_init: Initializing. RAM available for dynamic allocation:
I (246) heap_init: At 3FFAE6E0 len 00001920 (6 KiB): DRAM
I (252) heap_init: At 3FFB2930 len 0002D6D0 (181 KiB): DRAM
I (258) heap_init: At 3FFE0440 len 00003AE0 (14 KiB): D/IRAM
I (264) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM
I (271) heap_init: At 4008A454 len 00015BAC (86 KiB): IRAM
I (277) cpu_start: Pro cpu start user code
I (295) spi_flash: detected chip: gd
I (296) spi_flash: flash io: dio
W (296) spi_flash: Detected size(8192k) larger than the size in the binary image header(2048k). Using the size in the binary image header.
I (306) cpu_start: Starting scheduler on PRO CPU.
I (0) cpu_start: Starting scheduler on APP CPU.
I (317) CHECK_DISPLAY_LED: [ 1 ] Create display service instance
I (327) CHECK_DISPLAY_LED: LED pattern index is 0
W (327) LED_INDI: The led mode is invalid
I (2337) CHECK_DISPLAY_LED: LED pattern index is 1
I (4337) CHECK_DISPLAY_LED: LED pattern index is 2
W (4337) LED_INDI: The led mode is invalid
I (6337) CHECK_DISPLAY_LED: LED pattern index is 3
I (8337) CHECK_DISPLAY_LED: LED pattern index is 4
I (10337) CHECK_DISPLAY_LED: LED pattern index is 5
W (10337) LED_INDI: The led mode is invalid
I (12337) CHECK_DISPLAY_LED: LED pattern index is 6
W (12337) LED_INDI: The led mode is invalid
I (14337) CHECK_DISPLAY_LED: LED pattern index is 7
W (14337) LED_INDI: The led mode is invalid
I (16337) CHECK_DISPLAY_LED: LED pattern index is 8
W (16337) LED_INDI: The led mode is invalid
I (18337) CHECK_DISPLAY_LED: LED pattern index is 9
W (18337) LED_INDI: The led mode is invalid
I (20337) CHECK_DISPLAY_LED: LED pattern index is 10
W (20337) LED_INDI: The led mode is invalid
I (22337) CHECK_DISPLAY_LED: LED pattern index is 11
W (22337) LED_INDI: The led mode is invalid
I (24337) CHECK_DISPLAY_LED: LED pattern index is 12
W (24337) LED_INDI: The led mode is invalid
I (26337) CHECK_DISPLAY_LED: LED pattern index is 13
I (28337) CHECK_DISPLAY_LED: LED pattern index is 14
I (30337) CHECK_DISPLAY_LED: LED pattern index is 15
W (30337) LED_INDI: The led mode is invalid
I (32337) CHECK_DISPLAY_LED: LED pattern index is 16
W (32337) LED_INDI: The led mode is invalid
I (34337) CHECK_DISPLAY_LED: LED pattern index is 17
W (34337) LED_INDI: The led mode is invalid
I (36337) CHECK_DISPLAY_LED: LED pattern index is 18
W (36337) LED_INDI: The led mode is invalid
I (38337) CHECK_DISPLAY_LED: LED pattern index is 19
W (38337) LED_INDI: The led mode is invalid
I (40337) CHECK_DISPLAY_LED: LED pattern index is 20
I (42337) CHECK_DISPLAY_LED: LED pattern index is 21
I (44337) CHECK_DISPLAY_LED: LED pattern index is 22
W (44337) LED_INDI: The led mode is invalid
I (46337) CHECK_DISPLAY_LED: LED pattern index is 23
W (46337) LED_INDI: The led mode is invalid
I (48337) CHECK_DISPLAY_LED: LED pattern index is 24
W (48337) LED_INDI: The led mode is invalid
I (50337) CHECK_DISPLAY_LED: LED pattern index is 25
W (50337) LED_INDI: The led mode is invalid
I (52337) CHECK_DISPLAY_LED: LED pattern index is 26
W (52337) LED_INDI: The led mode is invalid
I (54337) CHECK_DISPLAY_LED: LED pattern index is 27
I (56337) CHECK_DISPLAY_LED: LED pattern index is 28
I (58337) CHECK_DISPLAY_LED: LED pattern index is 0
W (58337) LED_INDI: The led mode is invalid
I (60337) CHECK_DISPLAY_LED: LED pattern index is 1
I (62337) CHECK_DISPLAY_LED: LED pattern index is 2
W (62337) LED_INDI: The led mode is invalid
I (64337) CHECK_DISPLAY_LED: LED pattern index is 3
I (66337) CHECK_DISPLAY_LED: LED pattern index is 4
I (68337) CHECK_DISPLAY_LED: LED pattern index is 5
W (68337) LED_INDI: The led mode is invalid
I (70337) CHECK_DISPLAY_LED: LED pattern index is 6
W (70337) LED_INDI: The led mode is invalid
I (72337) CHECK_DISPLAY_LED: LED pattern index is 7
W (72337) LED_INDI: The led mode is invalidA complete log is as follows:
rst:0x1 (POWERON_RESET),boot:0x1f (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:2
load:0x3fff0030,len:7204
load:0x40078000,len:13212
load:0x40080400,len:4568
0x40080400: _init at ??:?
entry 0x400806f4
I (27) boot: ESP-IDF v4.2.2-1-g379ca2123 2nd stage bootloader
I (27) boot: compile time 15:01:00
I (27) boot: chip revision: 3
I (31) boot_comm: chip revision: 3, min. bootloader chip revision: 0
I (38) boot.esp32: SPI Speed : 40MHz
I (43) boot.esp32: SPI Mode : DIO
I (47) boot.esp32: SPI Flash Size : 2MB
I (52) boot: Enabling RNG early entropy source...
I (57) boot: Partition Table:
I (61) boot: ## Label Usage Type ST Offset Length
I (68) boot: 0 nvs WiFi data 01 02 00009000 00006000
I (76) boot: 1 phy_init RF data 01 01 0000f000 00001000
I (83) boot: 2 factory factory app 00 00 00010000 00100000
I (91) boot: End of partition table
I (95) boot_comm: chip revision: 3, min. application chip revision: 0
I (102) esp_image: segment 0: paddr=0x00010020 vaddr=0x3f400020 size=0x06c00 ( 27648) map
I (122) esp_image: segment 1: paddr=0x00016c28 vaddr=0x3ffb0000 size=0x020ac ( 8364) load
I (125) esp_image: segment 2: paddr=0x00018cdc vaddr=0x40080000 size=0x0733c ( 29500) load
0x40080000: _WindowOverflow4 at /hengyongchao/esp-idfs/esp-idf-v4.2.2-psram/components/freertos/xtensa/xtensa_vectors.S:1730
I (142) esp_image: segment 3: paddr=0x00020020 vaddr=0x400d0020 size=0x16d48 ( 93512) map
0x400d0020: _stext at ??:?
I (178) esp_image: segment 4: paddr=0x00036d70 vaddr=0x4008733c size=0x03118 ( 12568) load
0x4008733c: xthal_window_spill_nw at /Users/igrokhotkov/e/esp32/hal/hal/windowspill_asm.S:212
I (189) boot: Loaded app from partition at offset 0x10000
I (189) boot: Disabling RNG early entropy source...
I (190) cpu_start: Pro cpu up.
I (193) cpu_start: Application information:
I (198) cpu_start: Project name: check_display_led
I (204) cpu_start: App version: v2.2-228-g07116fa5-dirty
I (210) cpu_start: Compile time: Nov 12 2021 16:20:42
I (217) cpu_start: ELF file SHA256: b5d39a251613418c...
I (223) cpu_start: ESP-IDF: v4.2.2-1-g379ca2123
I (229) cpu_start: Starting app cpu, entry point is 0x40081618
0x40081618: call_start_cpu1 at /hengyongchao/esp-idfs/esp-idf-v4.2.2-psram/components/esp32/cpu_start.c:287
I (0) cpu_start: App cpu up.
I (239) heap_init: Initializing. RAM available for dynamic allocation:
I (246) heap_init: At 3FFAE6E0 len 00001920 (6 KiB): DRAM
I (252) heap_init: At 3FFB2930 len 0002D6D0 (181 KiB): DRAM
I (258) heap_init: At 3FFE0440 len 00003AE0 (14 KiB): D/IRAM
I (264) heap_init: At 3FFE4350 len 0001BCB0 (111 KiB): D/IRAM
I (271) heap_init: At 4008A454 len 00015BAC (86 KiB): IRAM
I (277) cpu_start: Pro cpu start user code
I (295) spi_flash: detected chip: gd
I (296) spi_flash: flash io: dio
W (296) spi_flash: Detected size(8192k) larger than the size in the binary image header(2048k). Using the size in the binary image header.
I (306) cpu_start: Starting scheduler on PRO CPU.
I (0) cpu_start: Starting scheduler on APP CPU.
I (317) CHECK_DISPLAY_LED: [ 1 ] Create display service instance
I (327) CHECK_DISPLAY_LED: LED pattern index is 0
W (327) LED_INDI: The led mode is invalid
I (2337) CHECK_DISPLAY_LED: LED pattern index is 1
I (4337) CHECK_DISPLAY_LED: LED pattern index is 2
W (4337) LED_INDI: The led mode is invalid
I (6337) CHECK_DISPLAY_LED: LED pattern index is 3
I (8337) CHECK_DISPLAY_LED: LED pattern index is 4
I (10337) CHECK_DISPLAY_LED: LED pattern index is 5
W (10337) LED_INDI: The led mode is invalid
I (12337) CHECK_DISPLAY_LED: LED pattern index is 6
W (12337) LED_INDI: The led mode is invalid
I (14337) CHECK_DISPLAY_LED: LED pattern index is 7
W (14337) LED_INDI: The led mode is invalid
I (16337) CHECK_DISPLAY_LED: LED pattern index is 8
W (16337) LED_INDI: The led mode is invalid
I (18337) CHECK_DISPLAY_LED: LED pattern index is 9
W (18337) LED_INDI: The led mode is invalid
I (20337) CHECK_DISPLAY_LED: LED pattern index is 10
W (20337) LED_INDI: The led mode is invalid
I (22337) CHECK_DISPLAY_LED: LED pattern index is 11
W (22337) LED_INDI: The led mode is invalid
I (24337) CHECK_DISPLAY_LED: LED pattern index is 12
W (24337) LED_INDI: The led mode is invalid
I (26337) CHECK_DISPLAY_LED: LED pattern index is 13
I (28337) CHECK_DISPLAY_LED: LED pattern index is 14
I (30337) CHECK_DISPLAY_LED: LED pattern index is 15
W (30337) LED_INDI: The led mode is invalid
I (32337) CHECK_DISPLAY_LED: LED pattern index is 16
W (32337) LED_INDI: The led mode is invalid
I (34337) CHECK_DISPLAY_LED: LED pattern index is 17
W (34337) LED_INDI: The led mode is invalid
I (36337) CHECK_DISPLAY_LED: LED pattern index is 18
W (36337) LED_INDI: The led mode is invalid
I (38337) CHECK_DISPLAY_LED: LED pattern index is 19
W (38337) LED_INDI: The led mode is invalid
I (40337) CHECK_DISPLAY_LED: LED pattern index is 20
I (42337) CHECK_DISPLAY_LED: LED pattern index is 21
I (44337) CHECK_DISPLAY_LED: LED pattern index is 22
W (44337) LED_INDI: The led mode is invalid
I (46337) CHECK_DISPLAY_LED: LED pattern index is 23
W (46337) LED_INDI: The led mode is invalid
I (48337) CHECK_DISPLAY_LED: LED pattern index is 24
W (48337) LED_INDI: The led mode is invalid
I (50337) CHECK_DISPLAY_LED: LED pattern index is 25
W (50337) LED_INDI: The led mode is invalid
I (52337) CHECK_DISPLAY_LED: LED pattern index is 26
W (52337) LED_INDI: The led mode is invalid
I (54337) CHECK_DISPLAY_LED: LED pattern index is 27
I (56337) CHECK_DISPLAY_LED: LED pattern index is 28
I (58337) CHECK_DISPLAY_LED: LED pattern index is 0
W (58337) LED_INDI: The led mode is invalid
I (60337) CHECK_DISPLAY_LED: LED pattern index is 1
I (62337) CHECK_DISPLAY_LED: LED pattern index is 2
W (62337) LED_INDI: The led mode is invalid
I (64337) CHECK_DISPLAY_LED: LED pattern index is 3
I (66337) CHECK_DISPLAY_LED: LED pattern index is 4
I (68337) CHECK_DISPLAY_LED: LED pattern index is 5
W (68337) LED_INDI: The led mode is invalid
I (70337) CHECK_DISPLAY_LED: LED pattern index is 6
W (70337) LED_INDI: The led mode is invalid
I (72337) CHECK_DISPLAY_LED: LED pattern index is 7
W (72337) LED_INDI: The led mode is invalidPlease use the following feedback channels:
- For technical queries, go to the esp32.com forum
- For a feature request or bug report, create a GitHub issue
We will get back to you as soon as possible.