SFE_LSM9DS0.h

/******************************************************************************
SFE_LSM9DS0.h
SFE_LSM9DS0 Library Header File
Jim Lindblom @ SparkFun Electronics
Original Creation Date: February 14, 2014 (Happy Valentines Day!)
Modified 14 Jul 2015 by Mike Hord to add Edison support
https://github.com/sparkfun/SparkFun_9DOF_Block_for_Edison_CPP_Library

This file prototypes the LSM9DS0 class, implemented in SFE_LSM9DS0.cpp. In
addition, it defines every register in the LSM9DS0 (both the Gyro and Accel/
Magnetometer registers).

** Supports only I2C connection! **

Development environment specifics:
  Code developed in Intel's Eclipse IOT-DK
  This code requires the Intel mraa library to function; for more
  information see https://github.com/intel-iot-devkit/mraa

This code is beerware; if you see me (or any other SparkFun employee) at the
local, and you've found our code helpful, please buy us a round!

Distributed as-is; no warranty is given.
******************************************************************************/
#ifndef __SFE_LSM9DS0_H__
#define __SFE_LSM9DS0_H__

#include <stdint.h>
#include "mraa.hpp"

////////////////////////////
// LSM9DS0 Gyro Registers //
////////////////////////////
#define WHO_AM_I_G			0x0F
#define CTRL_REG1_G			0x20
#define CTRL_REG2_G			0x21
#define CTRL_REG3_G			0x22
#define CTRL_REG4_G			0x23
#define CTRL_REG5_G			0x24
#define REFERENCE_G			0x25
#define STATUS_REG_G		0x27
#define OUT_X_L_G			0x28
#define OUT_X_H_G			0x29
#define OUT_Y_L_G			0x2A
#define OUT_Y_H_G			0x2B
#define OUT_Z_L_G			0x2C
#define OUT_Z_H_G			0x2D
#define FIFO_CTRL_REG_G		0x2E
#define FIFO_SRC_REG_G		0x2F
#define INT1_CFG_G			0x30
#define INT1_SRC_G			0x31
#define INT1_THS_XH_G		0x32
#define INT1_THS_XL_G		0x33
#define INT1_THS_YH_G		0x34
#define INT1_THS_YL_G		0x35
#define INT1_THS_ZH_G		0x36
#define INT1_THS_ZL_G		0x37
#define INT1_DURATION_G		0x38

//////////////////////////////////////////
// LSM9DS0 Accel/Magneto (XM) Registers //
//////////////////////////////////////////
#define OUT_TEMP_L_XM		0x05
#define OUT_TEMP_H_XM		0x06
#define STATUS_REG_M		0x07
#define OUT_X_L_M			0x08
#define OUT_X_H_M			0x09
#define OUT_Y_L_M			0x0A
#define OUT_Y_H_M			0x0B
#define OUT_Z_L_M			0x0C
#define OUT_Z_H_M			0x0D
#define WHO_AM_I_XM			0x0F
#define INT_CTRL_REG_M		0x12
#define INT_SRC_REG_M		0x13
#define INT_THS_L_M			0x14
#define INT_THS_H_M			0x15
#define OFFSET_X_L_M		0x16
#define OFFSET_X_H_M		0x17
#define OFFSET_Y_L_M		0x18
#define OFFSET_Y_H_M		0x19
#define OFFSET_Z_L_M		0x1A
#define OFFSET_Z_H_M		0x1B
#define REFERENCE_X			0x1C
#define REFERENCE_Y			0x1D
#define REFERENCE_Z			0x1E
#define CTRL_REG0_XM		0x1F
#define CTRL_REG1_XM		0x20
#define CTRL_REG2_XM		0x21
#define CTRL_REG3_XM		0x22
#define CTRL_REG4_XM		0x23
#define CTRL_REG5_XM		0x24
#define CTRL_REG6_XM		0x25
#define CTRL_REG7_XM		0x26
#define STATUS_REG_A		0x27
#define OUT_X_L_A			0x28
#define OUT_X_H_A			0x29
#define OUT_Y_L_A			0x2A
#define OUT_Y_H_A			0x2B
#define OUT_Z_L_A			0x2C
#define OUT_Z_H_A			0x2D
#define FIFO_CTRL_REG		0x2E
#define FIFO_SRC_REG		0x2F
#define INT_GEN_1_REG		0x30
#define INT_GEN_1_SRC		0x31
#define INT_GEN_1_THS		0x32
#define INT_GEN_1_DURATION	0x33
#define INT_GEN_2_REG		0x34
#define INT_GEN_2_SRC		0x35
#define INT_GEN_2_THS		0x36
#define INT_GEN_2_DURATION	0x37
#define CLICK_CFG			0x38
#define CLICK_SRC			0x39
#define CLICK_THS			0x3A
#define TIME_LIMIT			0x3B
#define TIME_LATENCY		0x3C
#define TIME_WINDOW			0x3D
#define ACT_THS				0x3E
#define ACT_DUR				0x3F

class LSM9DS0
{
public:
	// gyro_scale defines the possible full-scale ranges of the gyroscope:
	enum gyro_scale
	{
		G_SCALE_245DPS,		// 00:  245 degrees per second
		G_SCALE_500DPS,		// 01:  500 dps
		G_SCALE_2000DPS,	// 10:  2000 dps
	};
	// accel_scale defines all possible FSR's of the accelerometer:
	enum accel_scale
	{
		A_SCALE_2G,	// 000:  2g
		A_SCALE_4G,	// 001:  4g
		A_SCALE_6G,	// 010:  6g
		A_SCALE_8G,	// 011:  8g
		A_SCALE_16G	// 100:  16g
	};
	// mag_scale defines all possible FSR's of the magnetometer:
	enum mag_scale
	{
		M_SCALE_2GS,	// 00:  2Gs
		M_SCALE_4GS, 	// 01:  4Gs
		M_SCALE_8GS,	// 10:  8Gs
		M_SCALE_12GS,	// 11:  12Gs
	};
	// gyro_odr defines all possible data rate/bandwidth combos of the gyro:
	enum gyro_odr
	{							// ODR (Hz) --- Cutoff
		G_ODR_95_BW_125  = 0x0, //   95         12.5
		G_ODR_95_BW_25   = 0x1, //   95          25
		// 0x2 and 0x3 define the same data rate and bandwidth
		G_ODR_190_BW_125 = 0x4, //   190        12.5
		G_ODR_190_BW_25  = 0x5, //   190         25
		G_ODR_190_BW_50  = 0x6, //   190         50
		G_ODR_190_BW_70  = 0x7, //   190         70
		G_ODR_380_BW_20  = 0x8, //   380         20
		G_ODR_380_BW_25  = 0x9, //   380         25
		G_ODR_380_BW_50  = 0xA, //   380         50
		G_ODR_380_BW_100 = 0xB, //   380         100
		G_ODR_760_BW_30  = 0xC, //   760         30
		G_ODR_760_BW_35  = 0xD, //   760         35
		G_ODR_760_BW_50  = 0xE, //   760         50
		G_ODR_760_BW_100 = 0xF, //   760         100
	};
	// accel_oder defines all possible output data rates of the accelerometer:
	enum accel_odr
	{
		A_POWER_DOWN, 	// Power-down mode (0x0)
		A_ODR_3125,		// 3.125 Hz	(0x1)
		A_ODR_625,		// 6.25 Hz (0x2)
		A_ODR_125,		// 12.5 Hz (0x3)
		A_ODR_25,		// 25 Hz (0x4)
		A_ODR_50,		// 50 Hz (0x5)
		A_ODR_100,		// 100 Hz (0x6)
		A_ODR_200,		// 200 Hz (0x7)
		A_ODR_400,		// 400 Hz (0x8)
		A_ODR_800,		// 800 Hz (9)
		A_ODR_1600		// 1600 Hz (0xA)
	};

      // accel_abw defines all possible anti-aliasing filter rates of the accelerometer:
	enum accel_abw
	{
		A_ABW_773,		// 773 Hz (0x0)
		A_ABW_194,		// 194 Hz (0x1)
		A_ABW_362,		// 362 Hz (0x2)
		A_ABW_50,		//  50 Hz (0x3)
	};


	// mag_oder defines all possible output data rates of the magnetometer:
	enum mag_odr
	{
		M_ODR_3125,	// 3.125 Hz (0x00)
		M_ODR_625,	// 6.25 Hz (0x01)
		M_ODR_125,	// 12.5 Hz (0x02)
		M_ODR_25,	// 25 Hz (0x03)
		M_ODR_50,	// 50 (0x04)
		M_ODR_100,	// 100 Hz (0x05)
	};

	// We'll store the gyro, accel, and magnetometer readings in a series of
	// public class variables. Each sensor gets three variables -- one for each
	// axis. Call readGyro(), readAccel(), and readMag() first, before using
	// these variables!
	// These values are the RAW signed 16-bit readings from the sensors.
	int16_t gx, gy, gz; // x, y, and z axis readings of the gyroscope
	int16_t ax, ay, az; // x, y, and z axis readings of the accelerometer
	int16_t mx, my, mz; // x, y, and z axis readings of the magnetometer
  int16_t temperature;

	// LSM9DS0 -- LSM9DS0 class constructor
	// The constructor will set up a handful of private variables, and set the
	// communication mode as well.
	// Input:
	//	- gAddr = I2C address of the gyroscope.
	//	- xmAddr = I2C address of the accel/mag.
	LSM9DS0(uint8_t gAddr, uint8_t xmAddr);
	
	// begin() -- Initialize the gyro, accelerometer, and magnetometer.
	// This will set up the scale and output rate of each sensor. It'll also
	// "turn on" every sensor and every axis of every sensor.
	// Input:
	//	- gScl = The scale of the gyroscope. This should be a gyro_scale value.
	//	- aScl = The scale of the accelerometer. Should be a accel_scale value.
	//	- mScl = The scale of the magnetometer. Should be a mag_scale value.
	//	- gODR = Output data rate of the gyroscope. gyro_odr value.
	//	- aODR = Output data rate of the accelerometer. accel_odr value.
	//	- mODR = Output data rate of the magnetometer. mag_odr value.
	// Output: The function will return an unsigned 16-bit value. The most-sig
	//		bytes of the output are the WHO_AM_I reading of the accel. The
	//		least significant two bytes are the WHO_AM_I reading of the gyro.
	// All parameters have a defaulted value, so you can call just "begin()".
	// Default values are FSR's of:  245DPS, 2g, 2Gs; ODRs of 95 Hz for 
	// gyro, 100 Hz for accelerometer, 100 Hz for magnetometer.
	// Use the return value of this function to verify communication.
	uint16_t begin(gyro_scale gScl = G_SCALE_245DPS, 
				accel_scale aScl = A_SCALE_2G, mag_scale mScl = M_SCALE_2GS,
				gyro_odr gODR = G_ODR_95_BW_125, accel_odr aODR = A_ODR_50, 
				mag_odr mODR = M_ODR_50);
	
	// readGyro() -- Read the gyroscope output registers.
	// This function will read all six gyroscope output registers.
	// The readings are stored in the class' gx, gy, and gz variables. Read
	// those _after_ calling readGyro().
	void readGyro();
	
	// readAccel() -- Read the accelerometer output registers.
	// This function will read all six accelerometer output registers.
	// The readings are stored in the class' ax, ay, and az variables. Read
	// those _after_ calling readAccel().
	void readAccel();
	
	// readMag() -- Read the magnetometer output registers.
	// This function will read all six magnetometer output registers.
	// The readings are stored in the class' mx, my, and mz variables. Read
	// those _after_ calling readMag().
	void readMag();

	// readTemp() -- Read the temperature output register.
	// This function will read two temperature output registers.
	// The combined readings are stored in the class' temperature variables. 
	// Read those _after_ calling readTemp().
	void readTemp();
	
	// calcGyro() -- Convert from RAW signed 16-bit value to degrees per second
	// This function reads in a signed 16-bit value and returns the scaled
	// DPS. This function relies on gScale and gRes being correct.
	// Input:
	//	- gyro = A signed 16-bit raw reading from the gyroscope.
	float calcGyro(int16_t gyro);
	
	// calcAccel() -- Convert from RAW signed 16-bit value to gravity (g's).
	// This function reads in a signed 16-bit value and returns the scaled
	// g's. This function relies on aScale and aRes being correct.
	// Input:
	//	- accel = A signed 16-bit raw reading from the accelerometer.
	float calcAccel(int16_t accel);
	
	// calcMag() -- Convert from RAW signed 16-bit value to Gauss (Gs)
	// This function reads in a signed 16-bit value and returns the scaled
	// Gs. This function relies on mScale and mRes being correct.
	// Input:
	//	- mag = A signed 16-bit raw reading from the magnetometer.
	float calcMag(int16_t mag);
	
	// setGyroScale() -- Set the full-scale range of the gyroscope.
	// This function can be called to set the scale of the gyroscope to 
	// 245, 500, or 200 degrees per second.
	// Input:
	// 	- gScl = The desired gyroscope scale. Must be one of three possible
	//		values from the gyro_scale enum.
	void setGyroScale(gyro_scale gScl);
	
	// setAccelScale() -- Set the full-scale range of the accelerometer.
	// This function can be called to set the scale of the accelerometer to
	// 2, 4, 6, 8, or 16 g's.
	// Input:
	// 	- aScl = The desired accelerometer scale. Must be one of five possible
	//		values from the accel_scale enum.
	void setAccelScale(accel_scale aScl);
	
	// setMagScale() -- Set the full-scale range of the magnetometer.
	// This function can be called to set the scale of the magnetometer to
	// 2, 4, 8, or 12 Gs.
	// Input:
	// 	- mScl = The desired magnetometer scale. Must be one of four possible
	//		values from the mag_scale enum.
	void setMagScale(mag_scale mScl);
	
	// setGyroODR() -- Set the output data rate and bandwidth of the gyroscope
	// Input:
	//	- gRate = The desired output rate and cutoff frequency of the gyro.
	//		Must be a value from the gyro_odr enum (check above, there're 14).
	void setGyroODR(gyro_odr gRate);
	
	// setAccelODR() -- Set the output data rate of the accelerometer
	// Input:
	//	- aRate = The desired output rate of the accel.
	//		Must be a value from the accel_odr enum (check above, there're 11).
	void setAccelODR(accel_odr aRate); 	

  // setAccelABW() -- Set the anti-aliasing filter rate of the accelerometer
	// Input:
	//	- abwRate = The desired anti-aliasing filter rate of the accel.
	//		Must be a value from the accel_abw enum (check above, there're 4).
	void setAccelABW(accel_abw abwRate);

	// setMagODR() -- Set the output data rate of the magnetometer
	// Input:
	//	- mRate = The desired output rate of the mag.
	//		Must be a value from the mag_odr enum (check above, there're 6).
	void setMagODR(mag_odr mRate);

  // Since the Edison is not a real-time system, it's probably best to let the
  //  LSMDS0 set the pace of data collection, as sampling rate matters for some
  //  applications. These functions allow you to see if new data has been
  //  logged since the last read. Note that it does NOT check for overflow
  //  conditions!!!
  bool newXData();
  bool newMData();
  bool newGData();

  // If you want to know whether an overflow has occurred, there are bits for
  //  that. These functions check for those conditions.
  bool xDataOverflow();
  bool gDataOverflow();
  bool mDataOverflow();

private:	

  mraa::I2c* gyro;
  mraa::I2c* xm;
	// gScale, aScale, and mScale store the current scale range for each 
	// sensor. Should be updated whenever that value changes.
	gyro_scale gScale;
	accel_scale aScale;
	mag_scale mScale;
	
	// gRes, aRes, and mRes store the current resolution for each sensor. 
	// Units of these values would be DPS (or g's or Gs's) per ADC tick.
	// This value is calculated as (sensor scale) / (2^15).
	float gRes, aRes, mRes;
	
	// initGyro() -- Sets up the gyroscope to begin reading.
	// This function steps through all five gyroscope control registers.
	// Upon exit, the following parameters will be set:
	//	- CTRL_REG1_G = 0x0F: Normal operation mode, all axes enabled. 
	//		95 Hz ODR, 12.5 Hz cutoff frequency.
	//	- CTRL_REG2_G = 0x00: HPF set to normal mode, cutoff frequency
	//		set to 7.2 Hz (depends on ODR).
	//	- CTRL_REG3_G = 0x88: Interrupt enabled on INT_G (set to push-pull and
	//		active high). Data-ready output enabled on DRDY_G.
	//	- CTRL_REG4_G = 0x00: Continuous update mode. Data LSB stored in lower
	//		address. Scale set to 245 DPS. SPI mode set to 4-wire.
	//	- CTRL_REG5_G = 0x00: FIFO disabled. HPF disabled.
	void initGyro();
	
	// initAccel() -- Sets up the accelerometer to begin reading.
	// This function steps through all accelerometer related control registers.
	// Upon exit these registers will be set as:
	//	- CTRL_REG0_XM = 0x00: FIFO disabled. HPF bypassed. Normal mode.
	//	- CTRL_REG1_XM = 0x57: 100 Hz data rate. Continuous update.
	//		all axes enabled.
	//	- CTRL_REG2_XM = 0x00:  2g scale. 773 Hz anti-alias filter BW.
	//	- CTRL_REG3_XM = 0x04: Accel data ready signal on INT1_XM pin.
	void initAccel();
	
	// initMag() -- Sets up the magnetometer to begin reading.
	// This function steps through all magnetometer-related control registers.
	// Upon exit these registers will be set as:
	//	- CTRL_REG4_XM = 0x04: Mag data ready signal on INT2_XM pin.
	//	- CTRL_REG5_XM = 0x14: 100 Hz update rate. Low resolution. Interrupt
	//		requests don't latch. Temperature sensor disabled.
	//	- CTRL_REG6_XM = 0x00:  2 Gs scale.
	//	- CTRL_REG7_XM = 0x00: Continuous conversion mode. Normal HPF mode.
	//	- INT_CTRL_REG_M = 0x09: Interrupt active-high. Enable interrupts.
	void initMag();
	
	// gReadByte() -- Reads a byte from a specified gyroscope register.
	// Input:
	// 	- subAddress = Register to be read from.
	// Output:
	// 	- An 8-bit value read from the requested address.
	uint8_t gReadByte(uint8_t subAddress);
	
	// gReadBytes() -- Reads a number of bytes -- beginning at an address
	// and incrementing from there -- from the gyroscope.
	// Input:
	// 	- subAddress = Register to be read from.
	// 	- * dest = A pointer to an array of uint8_t's. Values read will be
	//		stored in here on return.
	//	- count = The number of bytes to be read.
	// Output: No value is returned, but the `dest` array will store
	// 	the data read upon exit.
	void gReadBytes(uint8_t subAddress, uint8_t * dest, uint8_t count);
	
	// gWriteByte() -- Write a byte to a register in the gyroscope.
	// Input:
	//	- subAddress = Register to be written to.
	//	- data = data to be written to the register.
	void gWriteByte(uint8_t subAddress, uint8_t data);
	
	// xmReadByte() -- Read a byte from a register in the accel/mag sensor
	// Input:
	//	- subAddress = Register to be read from.
	// Output:
	//	- An 8-bit value read from the requested register.
	uint8_t xmReadByte(uint8_t subAddress);
	
	// xmReadBytes() -- Reads a number of bytes -- beginning at an address
	// and incrementing from there -- from the accelerometer/magnetometer.
	// Input:
	// 	- subAddress = Register to be read from.
	// 	- * dest = A pointer to an array of uint8_t's. Values read will be
	//		stored in here on return.
	//	- count = The number of bytes to be read.
	// Output: No value is returned, but the `dest` array will store
	// 	the data read upon exit.
	void xmReadBytes(uint8_t subAddress, uint8_t * dest, uint8_t count);
	
	// xmWriteByte() -- Write a byte to a register in the accel/mag sensor.
	// Input:
	//	- subAddress = Register to be written to.
	//	- data = data to be written to the register.
	void xmWriteByte(uint8_t subAddress, uint8_t data);
	
	// calcgRes() -- Calculate the resolution of the gyroscope.
	// This function will set the value of the gRes variable. gScale must
	// be set prior to calling this function.
	void calcgRes();
	
	// calcmRes() -- Calculate the resolution of the magnetometer.
	// This function will set the value of the mRes variable. mScale must
	// be set prior to calling this function.
	void calcmRes();
	
	// calcaRes() -- Calculate the resolution of the accelerometer.
	// This function will set the value of the aRes variable. aScale must
	// be set prior to calling this function.
	void calcaRes();
	
};

#endif // SFE_LSM9DS0_H //