ST7789T3 ESP32 #3111

bbuster2 · 2023-12-14T15:34:06Z

bbuster2
Dec 14, 2023

I have bought a 1.83" ST7789T3 display but cannot get it working.

Display is bought here:
https://nl.aliexpress.com/item/1005005565821377.html?spm=a2g0o.order_list.order_list_main.11.205779d2rzxJEm&gatewayAdapt=glo2nld

Schematic:

In platformio, i use these biuld_flags:

build_flags = 
	-D USER_SETUP_LOADED=1
	-D ST7789_DRIVER=1
	-D SMOOTH_FONT=1
	-D TFT_MISO=-1
	-D TFT_MOSI=23
	-D TFT_SCLK=18
	-D TFT_CS=-1
	-D TFT_DC=2
	-D TFT_RST=4
	-D SPI_FREQUENCY=40000000
	-D SPI_READ_FREQUENCY=20000000

The display stays "black". I can control the backlight but i cannot get text or an image on the display.
I have the reset pin high (but also tried low), and the CS port connected to ground.

Is this display incompatible with the ESP32 or am i doing something wrong?

Bodmer · 2023-12-14T17:11:19Z

Bodmer
Dec 14, 2023
Maintainer

Try using the CS line on a GPIO pin. The reason is that the ST7789 is easy to lock up with garbage commands during power up.

Also run the Read_User_Setup sketch and check the output is correct, this shows whether the correct settings are being picked up.

0 replies

bbuster2 · 2023-12-14T17:51:51Z

bbuster2
Dec 14, 2023
Author

Thank you for your reply. Adding the CS pin didn't make a difference (also connected to the ESP32).

Here is my output:

[code]
TFT_eSPI ver = 2.5.41
Processor    = ESP32
Frequency    = 240MHz
Transactions = Yes
Interface    = SPI
Display driver = 7789
Display width  = 240
Display height = 320

MOSI    = GPIO 23
SCK     = GPIO 18
TFT_CS   = GPIO 27
TFT_DC   = GPIO 2
TFT_RST  = GPIO 4

Font GLCD   loaded
Smooth font enabled

Display SPI frequency = 40.00
[/code]

0 replies

bbuster2 · 2023-12-18T08:33:26Z

bbuster2
Dec 18, 2023
Author

Any idea?

0 replies

Bodmer · 2023-12-18T17:55:02Z

Bodmer
Dec 18, 2023
Maintainer

The Read_User_Setup output looks good. Check the connections are sound and correct. Check the supply voltage to the display is correct. Software options to try:

Use the alternative replacement driver, viz. -D ST7789_2_DRIVER=1
Add option -D TFT_SPI_MODE SPI_MODE0=1
Reduce the SPI frequency to 27MHz

You also need to define the width and height to get the coordinate offsets correct, but that would not stop the display working.
-D TFT_WIDTH=240
-D TFT_HEIGHT=280

0 replies

bbuster2 · 2023-12-19T08:40:50Z

bbuster2
Dec 19, 2023
Author

I tried but the same result.
I couldn't get -D TFT_SPI_MODE SPI_MODE0=1 to work
When i added that, i got the following error:

*** [.pio/build/esp32dev/firmware.elf] Implicit dependency /Users/{username}/.platformio/platforms/espressif32/builder/SPI_MODE0=1' not found, needed by target .pio/build/esp32dev/firmware.elf'.

-D USER_SETUP_LOADED=1
	-D ST7789_2_DRIVER=1
	; -D TFT_SPI_MODE SPI_MODE0=1
	-D TFT_SPI_MODE=1
	-D SPI_MODE0=1

	-D DISPLAY_WIDTH=280
	-D DISPLAY_HEIGHT=240
	-D TFT_WIDTH=280
	-D TFT_HEIGHT=240
	-D SMOOTH_FONT=1
	-D TFT_MISO=-1
	-D TFT_MOSI=23
	-D TFT_SCLK=18
	-D TFT_CS=27
	-D TFT_DC=2
	-D TFT_RST=4
	-D TFT_WIDTH=240
	-D TFT_HEIGHT=280
	-D SPI_FREQUENCY=27000000
	-D SPI_READ_FREQUENCY=20000000

But i am not sure if that can work. The display is still black

0 replies

bbuster2 · 2023-12-28T13:38:30Z

bbuster2
Dec 28, 2023
Author

My display looks really similar to this: https://www.buydisplay.com/1-83-inch-ips-tft-lcd-display-240x280-round-circle-screen-for-smart-watch

I see here the specifications show it is a NV3030B IC.
Can this work?

It is also 4 pin SPI

0 replies

Bodmer · 2023-12-28T22:00:43Z

Bodmer
Dec 28, 2023
Maintainer

That display may look similar but that does not mean yours has that NV3030B controller. You have to assume the vendors information is correct.

I made a mistake above, the option should read:

-D TFT_SPI_MODE=SPI_MODE0

And delete the line:
-D SPI_MODE0=1

0 replies

bbuster2 · 2023-12-29T11:09:32Z

bbuster2
Dec 29, 2023
Author

Thank you for your reply. Unfortunately i still cannot get anything on the display. It stays black

Maybe a really stupid question, but i don't see any chip on the display itself. It is just the screen with the 13 pin connector. Am i not missing something? (The driver chip?)

0 replies

bbuster2 · 2024-01-10T12:47:21Z

bbuster2
Jan 10, 2024
Author

Any idea?

0 replies

Bodmer · 2024-01-16T23:24:00Z

Bodmer
Jan 16, 2024
Maintainer

No further ideas on the problem.

I suggest you purchase a prebuilt board and get that running. That will help to identify the root cause (display/interface problem or library configuration issue. If you have access to an oscilloscope or logic analyser that may help debug the problem too.

0 replies

nstepanets · 2024-02-11T01:27:30Z

nstepanets
Feb 11, 2024

Most likely this display is on the NV3030B controller.

The controller is similar to ILI9341/GC9A01A but it seems that the initialization commands are different. I was able to get it working with ESP32 after using the code example from buydisplay.

1 reply

Gangwa-Labs Aug 23, 2024

can you post the code example from buydisplay? I downloaded the "8051 Interfacing and Demo Code" but can't seem to understand what I actually need to upload to my esp32

nstepanets · 2024-05-09T00:11:33Z

nstepanets
May 9, 2024

Any idea?

@bbuster2
If the question is still relevant, can you check the display with the changes from this pull request?
#3315

4 replies

Gangwa-Labs Aug 23, 2024

I have the exact same display and made the changes from this pull request and it did not work unfortunately and the screen is still full black

nstepanets Aug 23, 2024

The screen is completely black, and the backlight is on?

If the display is on the ST7789 controller, then it should at least display something (with artifacts)

Gangwa-Labs Aug 25, 2024

The screen is totally black without the backlight, shouldn't the display be on the new one from this pull request? NV3030B?

nstepanets Sep 4, 2024

It looks like something is not set up correctly, as the backlight works regardless of the controller used.

belpower01 · 2024-06-14T22:18:00Z

belpower01
Jun 14, 2024

{
LCD_RST = 1;
Delayms(10);
LCD_RST = 0;
Delayms(10);
LCD_RST = 1;
Delayms(120);

NV3030B_MCU8_8080_CMD(0xfd);//private_access
NV3030B_MCU8_8080_DAT(0x06);
NV3030B_MCU8_8080_DAT(0x08);

NV3030B_MCU8_8080_CMD(0x61);//add
NV3030B_MCU8_8080_DAT(0x07);//
NV3030B_MCU8_8080_DAT(0x04);//
//bias
NV3030B_MCU8_8080_CMD(0x62);//bias setting
NV3030B_MCU8_8080_DAT(0x00);//01
NV3030B_MCU8_8080_DAT(0x44);//04 44
NV3030B_MCU8_8080_DAT(0x45);//44 65 40

NV3030B_MCU8_8080_CMD(0x63);//
NV3030B_MCU8_8080_DAT(0x41);//
NV3030B_MCU8_8080_DAT(0x07);//
NV3030B_MCU8_8080_DAT(0x12);//
NV3030B_MCU8_8080_DAT(0x12);//

NV3030B_MCU8_8080_CMD(0x64);//
NV3030B_MCU8_8080_DAT(0x37);//
//VSP
NV3030B_MCU8_8080_CMD(0x65);//Pump1=4.7MHz //PUMP1 VSP
NV3030B_MCU8_8080_DAT(0x09);//D6-5:pump1_clk[1:0] clamp 28 2b
NV3030B_MCU8_8080_DAT(0x10);//6.26
NV3030B_MCU8_8080_DAT(0x21);
//VSN
NV3030B_MCU8_8080_CMD(0x66); //pump=2 AVCL
NV3030B_MCU8_8080_DAT(0x09); //clamp 08 0b 09
NV3030B_MCU8_8080_DAT(0x10); //10
NV3030B_MCU8_8080_DAT(0x21);
//add source_neg_time
NV3030B_MCU8_8080_CMD(0x67);//pump_sel
NV3030B_MCU8_8080_DAT(0x20);//21 20
NV3030B_MCU8_8080_DAT(0x40);
//gamma vap/van
NV3030B_MCU8_8080_CMD(0x68);//gamma vap/van
NV3030B_MCU8_8080_DAT(0x90);//
NV3030B_MCU8_8080_DAT(0x4c);//
NV3030B_MCU8_8080_DAT(0x7c);//
NV3030B_MCU8_8080_DAT(0x66);//66 46 VCOM

NV3030B_MCU8_8080_CMD(0xb1);//frame rate
NV3030B_MCU8_8080_DAT(0x0F);//0x0f fr_h[5:0] 0F
NV3030B_MCU8_8080_DAT(0x02);//0x02 fr_v[4:0] 02
NV3030B_MCU8_8080_DAT(0x01);//0x04 fr_div[2:0] 03

NV3030B_MCU8_8080_CMD(0xB4);
NV3030B_MCU8_8080_DAT(0x01); //01:1dot 00:column
////porch
NV3030B_MCU8_8080_CMD(0xB5);
NV3030B_MCU8_8080_DAT(0x02);//0x02 vfp[6:0]
NV3030B_MCU8_8080_DAT(0x02);//0x02 vbp[6:0]
NV3030B_MCU8_8080_DAT(0x0a);//0x0A hfp[6:0]
NV3030B_MCU8_8080_DAT(0x14);//0x14 hbp[6:0]

NV3030B_MCU8_8080_CMD(0xB6);
NV3030B_MCU8_8080_DAT(0x04);//
NV3030B_MCU8_8080_DAT(0x01);//
NV3030B_MCU8_8080_DAT(0x9f);//
NV3030B_MCU8_8080_DAT(0x00);//
NV3030B_MCU8_8080_DAT(0x02);//
////gamme sel
NV3030B_MCU8_8080_CMD(0xdf);//
NV3030B_MCU8_8080_DAT(0x11);//gofc_gamma_en_sel=1
////gamma_test1 A1#wangly
//3030b_gamma_new
//GAMMA---------------------------------/////////////

//GAMMA---------------------------------/////////////
NV3030B_MCU8_8080_CMD(0xE2);
NV3030B_MCU8_8080_DAT(0x13);//vrp0[5:0] V0
NV3030B_MCU8_8080_DAT(0x00);//vrp1[5:0] V1
NV3030B_MCU8_8080_DAT(0x00);//vrp2[5:0] V2
NV3030B_MCU8_8080_DAT(0x30);//vrp3[5:0] V61
NV3030B_MCU8_8080_DAT(0x33);//vrp4[5:0] V62
NV3030B_MCU8_8080_DAT(0x3f);//vrp5[5:0] V63

NV3030B_MCU8_8080_CMD(0xE5);
NV3030B_MCU8_8080_DAT(0x3f);//vrn0[5:0] V63
NV3030B_MCU8_8080_DAT(0x33);//vrn1[5:0] V62
NV3030B_MCU8_8080_DAT(0x30);//vrn2[5:0] V61
NV3030B_MCU8_8080_DAT(0x00);//vrn3[5:0] V2
NV3030B_MCU8_8080_DAT(0x00);//vrn4[5:0] V1
NV3030B_MCU8_8080_DAT(0x13);//vrn5[5:0] V0

NV3030B_MCU8_8080_CMD(0xE1);
NV3030B_MCU8_8080_DAT(0x00);//prp0[6:0] V15
NV3030B_MCU8_8080_DAT(0x57);//prp1[6:0] V51

NV3030B_MCU8_8080_CMD(0xE4);
NV3030B_MCU8_8080_DAT(0x58);//prn0[6:0] V51
NV3030B_MCU8_8080_DAT(0x00);//prn1[6:0] V15

NV3030B_MCU8_8080_CMD(0xE0);
NV3030B_MCU8_8080_DAT(0x01);//pkp0[4:0] V3
NV3030B_MCU8_8080_DAT(0x03);//pkp1[4:0] V7
NV3030B_MCU8_8080_DAT(0x0d);//pkp2[4:0] V21
NV3030B_MCU8_8080_DAT(0x0e);//pkp3[4:0] V29 //
NV3030B_MCU8_8080_DAT(0x0e);//pkp4[4:0] V37
NV3030B_MCU8_8080_DAT(0x0c);//pkp5[4:0] V45
NV3030B_MCU8_8080_DAT(0x15);//pkp6[4:0] V56
NV3030B_MCU8_8080_DAT(0x19);//pkp7[4:0] V60

NV3030B_MCU8_8080_CMD(0xE3);
NV3030B_MCU8_8080_DAT(0x1a);//pkn0[4:0] V60
NV3030B_MCU8_8080_DAT(0x16);//pkn1[4:0] V56
NV3030B_MCU8_8080_DAT(0x0c);//pkn2[4:0] V45
NV3030B_MCU8_8080_DAT(0x0f);//pkn3[4:0] V37
NV3030B_MCU8_8080_DAT(0x0e);//pkn4[4:0] V29 //
NV3030B_MCU8_8080_DAT(0x0d);//pkn5[4:0] V21
NV3030B_MCU8_8080_DAT(0x02);//pkn6[4:0] V7
NV3030B_MCU8_8080_DAT(0x01);//pkn7[4:0] V3
//GAMMA---------------------------------/////////////

//source
NV3030B_MCU8_8080_CMD(0xE6);
NV3030B_MCU8_8080_DAT(0x00);
NV3030B_MCU8_8080_DAT(0xff);//SC_EN_START[7:0] f0

NV3030B_MCU8_8080_CMD(0xE7);
NV3030B_MCU8_8080_DAT(0x01);//CS_START[3:0] 01
NV3030B_MCU8_8080_DAT(0x04);//scdt_inv_sel cs_vp_en
NV3030B_MCU8_8080_DAT(0x03);//CS1_WIDTH[7:0] 12
NV3030B_MCU8_8080_DAT(0x03);//CS2_WIDTH[7:0] 12
NV3030B_MCU8_8080_DAT(0x00);//PREC_START[7:0] 06
NV3030B_MCU8_8080_DAT(0x12);//PREC_WIDTH[7:0] 12

NV3030B_MCU8_8080_CMD(0xE8); //source
NV3030B_MCU8_8080_DAT(0x00); //VCMP_OUT_EN 81-
NV3030B_MCU8_8080_DAT(0x70); //chopper_sel[6:4]
NV3030B_MCU8_8080_DAT(0x00); //gchopper_sel[6:4] 60
////gate
NV3030B_MCU8_8080_CMD(0xEc);
NV3030B_MCU8_8080_DAT(0x52);//52

NV3030B_MCU8_8080_CMD(0xF1);
NV3030B_MCU8_8080_DAT(0x01);//te_pol tem_extend 00 01 03
NV3030B_MCU8_8080_DAT(0x01);
NV3030B_MCU8_8080_DAT(0x02);

NV3030B_MCU8_8080_CMD(0xF6);//
NV3030B_MCU8_8080_DAT(0x09);//
NV3030B_MCU8_8080_DAT(0x10);//
NV3030B_MCU8_8080_DAT(0x00);//
NV3030B_MCU8_8080_DAT(0x00);//40 3ПЯ2НЁµА

NV3030B_MCU8_8080_CMD(0xfd);
NV3030B_MCU8_8080_DAT(0xfa);
NV3030B_MCU8_8080_DAT(0xfc);

NV3030B_MCU8_8080_CMD(0x3a);
NV3030B_MCU8_8080_DAT(0x05);//SH 0x66

NV3030B_MCU8_8080_CMD(0x35);
NV3030B_MCU8_8080_DAT(0x00);

NV3030B_MCU8_8080_CMD(0x36);//bgr_[3]
NV3030B_MCU8_8080_DAT(0x00);//c0

NV3030B_MCU8_8080_CMD(0x21);

NV3030B_MCU8_8080_CMD(0x11); // exit sleep
Delayms(200);
NV3030B_MCU8_8080_CMD(0x29); // display on
Delayms(10);
}

/====================================================/
void address(void)
{
NV3030B_MCU8_8080_CMD(0x2A); //Column Address Set
NV3030B_MCU8_8080_DAT(0x00);
NV3030B_MCU8_8080_DAT(0x00);
NV3030B_MCU8_8080_DAT(0x00);
NV3030B_MCU8_8080_DAT(0xEF); /* 240 */

NV3030B_MCU8_8080_CMD(0x2B);   //Row Address Set   
NV3030B_MCU8_8080_DAT(0x00);
NV3030B_MCU8_8080_DAT(0x14);    /*  20  */
NV3030B_MCU8_8080_DAT(0x01);
NV3030B_MCU8_8080_DAT(0x2B);   /*  299  */
			   
NV3030B_MCU8_8080_CMD(0x2C);

}

/SLEEP IN*****/
void EnterSleep(void)
{
NV3030B_MCU8_8080_CMD(0x28);
NV3030B_MCU8_8080_CMD(0x10);
Delayms(120);
}

/SLEEP OUT*****/
void ExitSleep(void)
{

NV3030B_MCU8_8080_CMD(0x11);
Delayms(120);
NV3030B_MCU8_8080_CMD(0x29);
    Delayms(10);

}

1 reply

nstepanets Jun 18, 2024

NV3030B_MCU8_8080_CMD(0x3a);
NV3030B_MCU8_8080_DAT(0x05);//SH 0x66

According to the datasheet, the correct value is 0x55

NV3030B_MCU8_8080_CMD(0x35);
NV3030B_MCU8_8080_DAT(0x00);

Tearing effect line on - I'm not sure that modes that are not used on other displays should be enabled.

NV3030B_MCU8_8080_CMD(0x36);//bgr_[3]
NV3030B_MCU8_8080_DAT(0x00);//c0

This is the default value, there is no point in setting it again.

belpower01 · 2024-06-14T22:35:29Z

belpower01
Jun 14, 2024

void LCD_GPIO_Init(void)
{
GPIO_InitTypeDef GPIO_InitStructure;
RCC_AHBPeriphClockCmd(RCC_AHBPeriph_GPIOA, ENABLE);

GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_3|GPIO_Pin_4|GPIO_Pin_5;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_OUT;
GPIO_InitStructure.GPIO_OType = GPIO_OType_PP;
GPIO_Init(GPIOA, &GPIO_InitStructure);
GPIO_SetBits(GPIOA,GPIO_Pin_0|GPIO_Pin_1|GPIO_Pin_2|GPIO_Pin_3|GPIO_Pin_4|GPIO_Pin_5);

}

void LCD_Writ_Bus(u8 dat)
{
u8 i;
LCD_CS_Clr();
for(i=0;i<8;i++)
{
LCD_SCLK_Clr();
if(dat&0x80)
{
LCD_MOSI_Set();
}
else
{
LCD_MOSI_Clr();
}
LCD_SCLK_Set();
dat<<=1;
}
LCD_CS_Set();
}

void LCD_WR_DATA8(u8 dat)
{
LCD_Writ_Bus(dat);
}

void LCD_WR_DATA(u16 dat)
{
LCD_Writ_Bus(dat>>8);
LCD_Writ_Bus(dat);
}

void LCD_WR_REG(u8 dat)
{
LCD_DC_Clr();
LCD_Writ_Bus(dat);
LCD_DC_Set();
}

void LCD_Address_Set(u16 x1,u16 y1,u16 x2,u16 y2)
{
if(USE_HORIZONTAL==0)
{
LCD_WR_REG(0x2a);
LCD_WR_DATA(x1);
LCD_WR_DATA(x2);
LCD_WR_REG(0x2b);
LCD_WR_DATA(y1+20);
LCD_WR_DATA(y2+20);
LCD_WR_REG(0x2c);
}
else if(USE_HORIZONTAL==1)
{
LCD_WR_REG(0x2a);
LCD_WR_DATA(x1);
LCD_WR_DATA(x2);
LCD_WR_REG(0x2b);
LCD_WR_DATA(y1+20);
LCD_WR_DATA(y2+20);
LCD_WR_REG(0x2c);
}
else if(USE_HORIZONTAL==2)
{
LCD_WR_REG(0x2a);
LCD_WR_DATA(x1+20);
LCD_WR_DATA(x2+20);
LCD_WR_REG(0x2b);
LCD_WR_DATA(y1);
LCD_WR_DATA(y2);
LCD_WR_REG(0x2c);
}
else
{
LCD_WR_REG(0x2a);
LCD_WR_DATA(x1+20);
LCD_WR_DATA(x2+20);
LCD_WR_REG(0x2b);
LCD_WR_DATA(y1);
LCD_WR_DATA(y2);
LCD_WR_REG(0x2c);
}
}
void LCD_Init(void)
{
LCD_GPIO_Init();

LCD_RES_Set();
delay_ms(10);
LCD_RES_Clr();
delay_ms(10);
LCD_RES_Set();
delay_ms(120);

LCD_BLK_Set();

LCD_WR_REG(0xfd);
LCD_WR_DATA8(0x06);
LCD_WR_DATA8(0x08);

LCD_WR_REG(0x61);
LCD_WR_DATA8(0x07);
LCD_WR_DATA8(0x04);

LCD_WR_REG(0x62);
LCD_WR_DATA8(0x00);
LCD_WR_DATA8(0x44);
LCD_WR_DATA8(0x45);

LCD_WR_REG(0x63);
LCD_WR_DATA8(0x41);
LCD_WR_DATA8(0x07);
LCD_WR_DATA8(0x12);
LCD_WR_DATA8(0x12);

LCD_WR_REG(0x64);
LCD_WR_DATA8(0x37);
//VSP
LCD_WR_REG(0x65);
LCD_WR_DATA8(0x09);
LCD_WR_DATA8(0x10);
LCD_WR_DATA8(0x21);
//VSN
LCD_WR_REG(0x66); 
LCD_WR_DATA8(0x09); 
LCD_WR_DATA8(0x10); 
LCD_WR_DATA8(0x21);
//add source_neg_time
LCD_WR_REG(0x67);//pump_sel
LCD_WR_DATA8(0x20);//21 20
LCD_WR_DATA8(0x40);

//gamma vap/van
LCD_WR_REG(0x68);//gamma vap/van
LCD_WR_DATA8(0x90);//
LCD_WR_DATA8(0x4c);//
LCD_WR_DATA8(0x7C);//VCOM  
LCD_WR_DATA8(0x66);//

LCD_WR_REG(0xb1);//frame rate
LCD_WR_DATA8(0x0F);//0x0f fr_h[5:0] 0F
LCD_WR_DATA8(0x02);//0x02 fr_v[4:0] 02
LCD_WR_DATA8(0x01);//0x04 fr_div[2:0] 04

LCD_WR_REG(0xB4);
LCD_WR_DATA8(0x01); //01:1dot 00:column
////porch
LCD_WR_REG(0xB5);
LCD_WR_DATA8(0x02);//0x02 vfp[6:0]
LCD_WR_DATA8(0x02);//0x02 vbp[6:0]
LCD_WR_DATA8(0x0a);//0x0A hfp[6:0]
LCD_WR_DATA8(0x14);//0x14 hbp[6:0]

LCD_WR_REG(0xB6);
LCD_WR_DATA8(0x04);//
LCD_WR_DATA8(0x01);//
LCD_WR_DATA8(0x9f);//
LCD_WR_DATA8(0x00);//
LCD_WR_DATA8(0x02);//
////gamme sel
LCD_WR_REG(0xdf);//
LCD_WR_DATA8(0x11);//gofc_gamma_en_sel=1
////gamma_test1 A1#_wangly
//3030b_gamma_new_
//GAMMA---------------------------------/////////////

//GAMMA---------------------------------/////////////
LCD_WR_REG(0xE2);	
LCD_WR_DATA8(0x13);//vrp0[5:0]	V0 13
LCD_WR_DATA8(0x00);//vrp1[5:0]	V1 
LCD_WR_DATA8(0x00);//vrp2[5:0]	V2 
LCD_WR_DATA8(0x30);//vrp3[5:0]	V61 
LCD_WR_DATA8(0x33);//vrp4[5:0]	V62 
LCD_WR_DATA8(0x3f);//vrp5[5:0]	V63

LCD_WR_REG(0xE5);	
LCD_WR_DATA8(0x3f);//vrn0[5:0]	V63
LCD_WR_DATA8(0x33);//vrn1[5:0]	V62	
LCD_WR_DATA8(0x30);//vrn2[5:0]	V61 
LCD_WR_DATA8(0x00);//vrn3[5:0]	V2 
LCD_WR_DATA8(0x00);//vrn4[5:0]	V1 
LCD_WR_DATA8(0x13);//vrn5[5:0]  V0 13

LCD_WR_REG(0xE1);	
LCD_WR_DATA8(0x00);//prp0[6:0]	V15
LCD_WR_DATA8(0x57);//prp1[6:0]	V51 

LCD_WR_REG(0xE4);	
LCD_WR_DATA8(0x58);//prn0[6:0]	V51 
LCD_WR_DATA8(0x00);//prn1[6:0]  V15

LCD_WR_REG(0xE0);
LCD_WR_DATA8(0x01);//pkp0[4:0]	V3 
LCD_WR_DATA8(0x03);//pkp1[4:0]	V7  
LCD_WR_DATA8(0x0d);//pkp2[4:0]	V21
LCD_WR_DATA8(0x0e);//pkp3[4:0]	V29 
LCD_WR_DATA8(0x0e);//pkp4[4:0]	V37 
LCD_WR_DATA8(0x0c);//pkp5[4:0]	V45 
LCD_WR_DATA8(0x15);//pkp6[4:0]	V56 
LCD_WR_DATA8(0x19);//pkp7[4:0]	V60 

LCD_WR_REG(0xE3);	
LCD_WR_DATA8(0x1a);//pkn0[4:0]	V60 
LCD_WR_DATA8(0x16);//pkn1[4:0]	V56 
LCD_WR_DATA8(0x0C);//pkn2[4:0]	V45 
LCD_WR_DATA8(0x0f);//pkn3[4:0]	V37 
LCD_WR_DATA8(0x0e);//pkn4[4:0]	V29 
LCD_WR_DATA8(0x0d);//pkn5[4:0]	V21 
LCD_WR_DATA8(0x02);//pkn6[4:0]	V7  
LCD_WR_DATA8(0x01);//pkn7[4:0]	V3 
//GAMMA---------------------------------/////////////

//source
LCD_WR_REG(0xE6);
LCD_WR_DATA8(0x00);
LCD_WR_DATA8(0xff);//SC_EN_START[7:0] f0

LCD_WR_REG(0xE7);
LCD_WR_DATA8(0x01);//CS_START[3:0] 01
LCD_WR_DATA8(0x04);//scdt_inv_sel cs_vp_en
LCD_WR_DATA8(0x03);//CS1_WIDTH[7:0] 12
LCD_WR_DATA8(0x03);//CS2_WIDTH[7:0] 12
LCD_WR_DATA8(0x00);//PREC_START[7:0] 06
LCD_WR_DATA8(0x12);//PREC_WIDTH[7:0] 12

LCD_WR_REG(0xE8); //source
LCD_WR_DATA8(0x00); //VCMP_OUT_EN 81-
LCD_WR_DATA8(0x70); //chopper_sel[6:4]
LCD_WR_DATA8(0x00); //gchopper_sel[6:4] 60
////gate
LCD_WR_REG(0xEc);
LCD_WR_DATA8(0x52);//52

LCD_WR_REG(0xF1);
LCD_WR_DATA8(0x01);//te_pol tem_extend 00 01 03
LCD_WR_DATA8(0x01);
LCD_WR_DATA8(0x02);


LCD_WR_REG(0xF6);
LCD_WR_DATA8(0x09);
LCD_WR_DATA8(0x10);
LCD_WR_DATA8(0x00);//
LCD_WR_DATA8(0x00);//40 3ПЯ2НЁµА

LCD_WR_REG(0xfd);
LCD_WR_DATA8(0xfa);
LCD_WR_DATA8(0xfc);

LCD_WR_REG(0x3a);
LCD_WR_DATA8(0x05);//

LCD_WR_REG(0x35);
LCD_WR_DATA8(0x00);

LCD_WR_REG(0x36);
if(USE_HORIZONTAL==0)LCD_WR_DATA8(0x08);
else if(USE_HORIZONTAL==1)LCD_WR_DATA8(0xC8);
else if(USE_HORIZONTAL==2)LCD_WR_DATA8(0x78);
else LCD_WR_DATA8(0xA8);


LCD_WR_REG(0x21); 

LCD_WR_REG(0x11); // exit sleep
delay_ms(200);
LCD_WR_REG(0x29); // display on
delay_ms(10);

}

0 replies

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

ST7789T3 ESP32 #3111

{{title}}

Replies: 14 comments 6 replies

{{title}}

{{title}}

{{editor}}'s edit

{{editor}}'s edit

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{editor}}'s edit

{{editor}}'s edit

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

{{title}}

Select a reply

ST7789T3 ESP32 #3111

Replies: 14 comments · 6 replies

Bodmer Dec 14, 2023 Maintainer

bbuster2 Dec 14, 2023 Author

bbuster2 Dec 18, 2023 Author

Bodmer Dec 18, 2023 Maintainer

bbuster2 Dec 19, 2023 Author

bbuster2 Dec 28, 2023 Author

Bodmer Dec 28, 2023 Maintainer

bbuster2 Dec 29, 2023 Author

bbuster2 Jan 10, 2024 Author

Bodmer Jan 16, 2024 Maintainer

Replies: 14 comments 6 replies

Bodmer
Dec 14, 2023
Maintainer

bbuster2
Dec 14, 2023
Author

bbuster2
Dec 18, 2023
Author

Bodmer
Dec 18, 2023
Maintainer

bbuster2
Dec 19, 2023
Author

bbuster2
Dec 28, 2023
Author

Bodmer
Dec 28, 2023
Maintainer

bbuster2
Dec 29, 2023
Author

bbuster2
Jan 10, 2024
Author

Bodmer
Jan 16, 2024
Maintainer